Pretty Nice Web Site !!!! I have a XL4 and I am very happy with it. Good luck selling it. AL www.poconodigitalwoodshop.com **************It's only a deal...
While I am no longer associated with Ripsaw, the product line, nor it's current manufacturer, I did stay in touch with the blade manufacturer. For over 20...
Hi, I have a ripsaw that I've been using for about five years with no significant problems. However, I now have a problem with the blade moving upward (at...
This is a Snow Blower story but if you have a problem with your XL4 with the Honda only running with the choke on full this may help. Last time I used my mill...
I think I want to sell my Ripsaw, with a Sthill 065 on it. I have it for many years but it is still a low timer tool. I don't need it anymore since I bought a...
Ripsawdeb: The carbide guide adjustment procedure (pdf version on the owners download page)indicates using a piece of paper above and below the blade to set...
HYPERLINK "http://www.suffolkmachinery.com/video.asp"http://www.suffolkmachinery.com/v ideo.asp I bought the video and glad I did. Dennis Thornton (on a...
We have encountered the same problem. At a woodland owners conference a few years ago I sat next to a sawmill guru. He told me that the small diameter wheels...
Hello, Al here in PA. I was planning to buy the setter for my XL4 in the future.... Have the same problem too. For now I am just building up my pile of ...
I've noticed that at times that I'll start getting wavy cuts and a blade change will cure it. The blade will still seem to be sharp but the set is near gone....
I recently bought a new Ripsaw and haven't had much time to use it, today being about the second time out (still using the original blade). I noticed when...
Deb, thanks for the reply. I did a follow-up post to the original with the results of my conversation with Roland but every time I do a reply to a message, I...
I thought I'd start a post to get a few opinions/procedures on your method of bandsaw blade cleaning/sharpening. I'd also like to get opinions on blade...
Scott I finally took a photo of what we discuss few weeks ago. Here is the pic [IMG]http://img228.imageshack.us/img228/4779/dentsripsaw7hs.jpg[/IMG] What do...
I recently bought a ripsaw setup and have enjoyed it so far. I really don't have enough experience with it to have any specific questions yet, just wanted to...
Last spring, I made a film (documentary) about my working with my new sawmill. (QuickTime). It's only in french, sorry. But I hope you'll like the images. ...
I've about decided to invest in a Ripsaw (if I can get past the issues with air drying)and had a question or two. I've read a post or two where an alaskan mill...
Your Gilbert was at least for awhile called "Morewood" and I gather the namer was aware of "Norwood" and thought "Morewood" was appropriate. I have a Norwood...
Hi Kevin. I bought my ripsaw here, it didn't come with a guide but was only a $1000 US (That post got taken down for some reason??). You could also try the...
... I bought the RipSaw when I was in Minnesota, I had 12 acres of trees and wanted lumber. I didn't have the means to move the logs & my dollars were limited....
I have an twin engine Alaskan, a Delta Lumber Company and my Norwood. Never used the Delta but I assume that it's similar to the RipSaw being luggable but with...
sawmillexchange.com I bought my Norwood on the Sawmillexchange.com and was happy. Had some confusion over the US/Canadian exchange! But we worked it out. ...
My guess it that you've used your chainsaw mill more than I've used mine, but I have run quite a bit thru my Norwood band mill. I would like to add a comment...
I've seen very little online and never a picture. Can't find a thing on the Delta site. I will try to either scan a drawing or picture on the manual or take a...
Having problems with message search?
