Welcome to the Regenerative Receivers Group. Having just been activated, i guess this is the first post. Please let me know if there are any questions gary...
2
Prof. Arnaldo Coro An...
coro@...
Nov 18, 2004 5:02 am
Si amigos ! This is certainly a great idea... So let's put it to work right now... I hope that the list will be joined by many homebrewers of regenerative ...
Well, hi there, Bry! Looks like for now it's just the few of us, possibly only two. I posted Arnie, perhaps he might either come on board, or tell some of his...
4
Prof. Arnaldo Coro An...
coro@...
Nov 18, 2004 5:07 am
Hi amigos !!! I am already here !!! Just received my first message from the list ... IT WORKS !!! BTW Gary,,, our good amigo AL Waller worked out the problems...
In a message dated 11/18/2004 12:05:39 AM Eastern Standard Time, coro@... ... I recall an article written in '73 back sometime in 1982 or 3, which was the...
Regen set users and builders, i would like to direct your attention to the following link which i have featured on my site for a couple years now : <A...
For some reason I am not getting the e-mails... Answering this one on the web page. I will check my settings. Hi Gary - Hi Arnie! Invited several other folks...
Bry, let me know if you get this response on the regenrx list, i will also copy direct to you off list until we know for sure you are receiving posts. Perhaps...
Arnie, let me know if you are getting posts from the Regenrx list, Bry had mentioned he was not, and i need to be sure the settings are correct. I am getting...
12
Prof. Arnaldo Coro An...
coro@...
Nov 19, 2004 2:32 pm
*Sure amigo Gary !!! No problem... In my Dxers Unlimited weekend edition I will promote the new list among the listeners. As you know there are many...
13
Prof. Arnaldo Coro An...
coro@...
Nov 19, 2004 2:39 pm
Yesterday I was trying to remember more about my 3S4 regenerative. It was all battery power... size D cell for filament and 22.5 volts for the plate. It used a...
For the benefit of those who are just now getting e-mails, i will be re-posting a few messages of interest regarding some neat sites and projects. While i have...
(Re-post, for benefit of new members) Regen set users and builders, i would like to direct your attention to the following link which i have featured on my...
In a message dated 11/19/04 9:43:19 AM Eastern Standard Time, coro@... ... ******* Sounds like a great idea to me! I might keep a sharp eye out for...
19
Prof. Arnaldo Coro An...
coro@...
Nov 19, 2004 4:19 pm
*Hi amigos ! Already having a lot of fun with this new REGENRX list !!! The 3S4 radio came with a "Ferri-Loopstick" antenna coil that also acted as the...
... Hi Arnie - it is good to see you here. The subscribing procedure is at the bottom of every message, including the one you just sent asking how to do it! ...
I say YES, YES YES -- we can even try out different tubes in the same design (1T4, 1U4, 3V4, etc.) P.S. - Good to hear from you again Arnie (even if it's not...
Dear Fellow Regeneratophiles, Just joined the list, and thanks for such a great idea for a group. Have built regens off and on for about 20 years, tube and...
A little while ago I built the N1TEV "Simple regen radio for beginners" September 2000 QST. It didn't work. I measured the voltages as shown in the schematic,...
FOR SALE: MDL HI-Q Inductance Type "A" PLUG-IN, 4-PIN COILS. These are some really nice commercially made coils. Link coupled types, except one as noted... ...
... One suggestion Tracy - you can uise a Grid Dip Meter (GDO) to test your coils. Put your parallel tuned circuit together and run that GDO on it and you will...
29
Prof. Arnaldo Coro An...
coro@...
Nov 21, 2004 10:06 pm
A true GRID DIP.... not "gate dip" or " base dip" meter is essential for homebrewing of any RF circuitry. No matter how good your physics and maths...
Hi fellow Regen-A-Holics, I couldn't resist the opportunity to join the group. Thanks to Tracy, N4LGH, for the invitation on QRP-L. You can see my latest...
