Anyone ever ran into this error code. I am in the process of updating this software so if that is whats going on I am fine but if not I need to know what the...
Does anyone have the chart depicting the DIP switch channel settings for the Tait T800 Series repeater? These are programmed via EEPROM and the DIP settings...
Does anyone have a copy of the Service Manual for this radio ? I am trying to confirm the pin-out for the programming connector. Thanks, Dick, W1KSZ...
if the radio came 450-512mhz, then you're stuck and I know of no way of changing it ... From: Dalton To: radio-programming@yahoogroups.com Sent: Wednesday,...
I'm having some problems programming a TK-350. I'm using a Windows XP machine with DOSBox and when I try to read or write the radio the software just says to...
hello all well in need of software for my old ic-f40 ht. i can't find my copy and beside's going to russiaetc.. is there anyone that can help?. also i still...
muliti cable After market rib for many different radios, I use it for my Maxtrac, CDM, HT-750 and some other radios that I'm not sure of ... From: ian dean To:...
hi all I have CPS R06.04.00 and i get a error message when i tried to read the radio "Unsupported Model" and next it says "Application does not support reading...
I am looking for some scrap, junked out Vertex FTL-1011,2011,or 7011 mobile radios for parts. I need the front panel display board from a 24 channel unit to...
Hello all I have decided to sell my 70-1000 programmer; I no longer have any Midland radios, so it's surplus to my needs. Comes with ac cord, instruction and...
I have a CDM-1250 & 1550 and both are remote mounted in one car, I'm using a Octopus rib and I can program the radios just fine when NOT remote mounted, I get...
Hi everyone! I am new to this group. I've been a licenced HAM for about 3 years. My question is this... I am setting up an IRLP simplex node with a GM300...
I PURCHASED A CDM 1550 LS RADIO THINKING IT COULD BE PROGRAMED WITH OUT A TRUNKING SYSTEM IN PLACE.. JUST WANTED IT TO WORK LIKE AN NORMAL RADIO WITH OUT...
Have a spectra MLM ver 616, has Zones. When I set the radio to RFMODEM mode via RSS, I get garbage on the display. I'd like to know what model # does RF MODEM...
Hello, My question is geared more towards a BCT15 scanner. If anyone lives in the Waukegan IL area and has successfully programmed the BCT with the local...
Good Afternoon. I am putting in a AFG 2008 proposal this week and have most of the budget numbers and such worked out. However, the persistent question of...
I am looking for a Rib for a P1225. I have the software for this radio and would like to obtain a rib so that I can program it. Can someone point me in the...
Can some on please e-mail me at cybercamsemail (at) aol (dot) com i just got my hands on a ic-f30gt and cable you can put the find the missing part there of...
OK - I may have screwed up. Here's what I did: 1: Read SaberII codeplug with RSS version 5. 2: Tried to program codeplug back in SaberII. 3: Saber showed error...
Hi all. I have a problem with my programming software. My new laptop doesn't open the software properly. It seems that any character that isn't a letter, is...
Hello I need help in waris lab tool I open waris lab connect rib flash adapter and original cable open firmware adapter in position "A" procced program...
For the first time I attempted to reprogram a channel on my F30GT in the field. I have the radio programmed into banks and the channel I was after was in bank...
Anyone use the above pc sucessfully on programing the older kenwood cdf kpg49 software. Were you able to slow it down enought to work ok. Lost my main laptop...
Here is what I have found and it pisses me off to no end.... I ordered the above part number from the big/\/\ and it shows up in two days (yea) but now here is...
