G'day all,
I am after some information on some radios that would be suitable to use as
a repeater. I have heard about radios such as the Philips 800 and 900 series
being able to be used as repeaters, but it is difficult to find information
on them. The repeater would be working on a commercial frequency between
470-500 MHz and possible at a later stage would be used as a UHF CB
repeater. I would like to it as cheap as possible if possible! A 'No Frills'
operation if you know what I mean. Also what else would I need in order of
antennas, diplexers etc? If fact, what is a diplexer??

Many thanks for your help in advance,
Jim
________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com

Hi Jim; one of the eaisest ways to make a repeater from two radios on
470-500 mhz would be the comercial phillips fm900 series. these are
programable with a e-prom burner and the program is found eaisly - if you
need it contact me, and there are a number of ways to set up the two. These
radios will put out a max of 25W selectable and they go for no more than 300
each for a remote head version (fm92 100 ch) hope this helped. As for
antennas is it going to be on a tower or just off a metal pole?

David

G'day David,
Thanks for your reply.
I am planning on using two 92's as the radios, but how can I wire them
together so that the TX is triggered when the other one RX? This is the part
where I am completely stuffed!

I plan on using poles for the antennas...no tower as yet!

Thanks you for your assistance,
Jim


>From: "David Edwards" <hsvdude@...>
>Reply-To: radio-programming@egroups.com
>To: <radio-programming@egroups.com>
>Subject: Re: [radio-prog@onelist] Digest Number 70
>Date: Fri, 5 May 2000 17:37:50 +1000
>
>Hi Jim; one of the eaisest ways to make a repeater from two radios on
>470-500 mhz would be the comercial phillips fm900 series. these are
>programable with a e-prom burner and the program is found eaisly - if you
>need it contact me, and there are a number of ways to set up the two. These
>radios will put out a max of 25W selectable and they go for no more than
>300
>each for a remote head version (fm92 100 ch) hope this helped. As for
>antennas is it going to be on a tower or just off a metal pole?
>
>David

________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com

Question --

Is it at all possible to convert a PRM8020T (trunking only radio) to
conventional radio, receive only, operates in the 450-470 mhz.

Paul

What model is best for UHF Cb? TK801-2 or TK801-3 ? Wht is it that
out of a few of these i have tested they do anywhere between 25w &
45w output? cheers

Can anyone provide me with availablity of programming software and
details of the cable and interface for programming the TK240 and TK-340
radios.  I think the software is KGP9.


Denis Mckay

FOR SALE

PRM8020T, 400-440mhz complete with power lead, ext speaker, bracket.

4@ $300 each
3@ $250 each (couple of buttons missing on these)

10% disc of purchase of 2 or more to the same buyer.

BE QUICK

Regards
Paul

are thay tk240d tk340d ?
if so you need software
if not you can short link an self program
----- Original Message -----
From: vk2dmr <vk2dmr@...>
To: <radio-programming@egroups.com>
Sent: Saturday, 6 May 2000 11:10
Subject: [radio-prog@onelist] KGP9 for TK-340


> Can anyone provide me with availablity of programming software and
> details of the cable and interface for programming the TK240 and TK-340
> radios.  I think the software is KGP9.
>
>
> Denis Mckay
>
>
>
> ------------------------------------------------------------------------
> FREE shipping, 30-Day No Question Returns, daily giveaways
> and much, much more at zZounds.com. Your music gear superstore!
> http://click.egroups.com/1/3731/4/_/638173/_/957575526/
> ------------------------------------------------------------------------
>
> Community email addresses:
>   Post message: radio-programming@onelist.com
>   Subscribe:    radio-programming-subscribe@onelist.com
>   Unsubscribe:  radio-programming-unsubscribe@onelist.com
>   List owner:   radio-programming-owner@onelist.com
>
> Shortcut URL to this page:
>   http://www.onelist.com/community/radio-programming

does anyone have the communiqué gx2007V (TB) software? I've got the
2007VE software but that's for the selcall beast, seems that this
software won't do the standard unit.

and as communiqué don't exist anymore not much point  in asking them!!!

Derrick@...

You might take a look at the programming circuits on my web page and see if
any of them will work. http://w3.pca.net/~cpclark

Craig Clark

----- Original Message -----
From: "shayne" <sde@...>
To: <radio-programming@egroups.com>
Sent: Saturday, May 06, 2000 3:05 AM
Subject: Re: [radio-prog@onelist] KGP9 for TK-340


> are thay tk240d tk340d ?
> if so you need software
> if not you can short link an self program
> ----- Original Message -----
> From: vk2dmr <vk2dmr@...>
> To: <radio-programming@egroups.com>
> Sent: Saturday, 6 May 2000 11:10
> Subject: [radio-prog@onelist] KGP9 for TK-340
>
>
> > Can anyone provide me with availablity of programming software and
> > details of the cable and interface for programming the TK240 and TK-340
> > radios.  I think the software is KGP9.
> >
> >
> > Denis Mckay
> >
> >
> >
> > ------------------------------------------------------------------------
> > FREE shipping, 30-Day No Question Returns, daily giveaways
> > and much, much more at zZounds.com. Your music gear superstore!
> > http://click.egroups.com/1/3731/4/_/638173/_/957575526/
> > ------------------------------------------------------------------------
> >
> > Community email addresses:
> >   Post message: radio-programming@onelist.com
> >   Subscribe:    radio-programming-subscribe@onelist.com
> >   Unsubscribe:  radio-programming-unsubscribe@onelist.com
> >   List owner:   radio-programming-owner@onelist.com
> >
> > Shortcut URL to this page:
> >   http://www.onelist.com/community/radio-programming
>
>
> ------------------------------------------------------------------------
> FREE shipping, 30-Day No Question Returns, daily giveaways
> and much, much more at zZounds.com. Your music gear superstore!
> http://click.egroups.com/1/3736/4/_/638173/_/957600412/
> ------------------------------------------------------------------------
>
> Community email addresses:
>   Post message: radio-programming@onelist.com
>   Subscribe:    radio-programming-subscribe@onelist.com
>   Unsubscribe:  radio-programming-unsubscribe@onelist.com
>   List owner:   radio-programming-owner@onelist.com
>
> Shortcut URL to this page:
>   http://www.onelist.com/community/radio-programming
>

I got it. Thank you for your reply, Ed.
----- Original Message -----
From: shayne <sde@...>
To: <radio-programming@egroups.com>
Sent: Saturday, May 06, 2000 1:05 AM
Subject: Re: [radio-prog@onelist] KGP9 for TK-340


> are thay tk240d tk340d ?
> if so you need software
> if not you can short link an self program
> ----- Original Message -----
> From: vk2dmr <vk2dmr@...>
> To: <radio-programming@egroups.com>
> Sent: Saturday, 6 May 2000 11:10
> Subject: [radio-prog@onelist] KGP9 for TK-340
>
>
> > Can anyone provide me with availablity of programming software and
> > details of the cable and interface for programming the TK240 and TK-340
> > radios.  I think the software is KGP9.
> >
> >
> > Denis Mckay
> >
> >
> >
> > ------------------------------------------------------------------------
> > FREE shipping, 30-Day No Question Returns, daily giveaways
> > and much, much more at zZounds.com. Your music gear superstore!
> > http://click.egroups.com/1/3731/4/_/638173/_/957575526/
> > ------------------------------------------------------------------------
> >
> > Community email addresses:
> >   Post message: radio-programming@onelist.com
> >   Subscribe:    radio-programming-subscribe@onelist.com
> >   Unsubscribe:  radio-programming-unsubscribe@onelist.com
> >   List owner:   radio-programming-owner@onelist.com
> >
> > Shortcut URL to this page:
> >   http://www.onelist.com/community/radio-programming
>
>
> ------------------------------------------------------------------------
> FREE shipping, 30-Day No Question Returns, daily giveaways
> and much, much more at zZounds.com. Your music gear superstore!
> http://click.egroups.com/1/3736/4/_/638173/_/957600412/
> ------------------------------------------------------------------------
>
> Community email addresses:
>   Post message: radio-programming@onelist.com
>   Subscribe:    radio-programming-subscribe@onelist.com
>   Unsubscribe:  radio-programming-unsubscribe@onelist.com
>   List owner:   radio-programming-owner@onelist.com
>
> Shortcut URL to this page:
>   http://www.onelist.com/community/radio-programming
>
>

Hi all
      Does anybody have any info on the Tait 2020 programming cable,are any
other cables compatible with this unit? eg. PRM80,Sawtron,Icom etc.
                                     Thanks in advance
                                      Nick.
________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com

Further to this
Is there any software around for the units
or do you have to manualy Hex edit the files.
also wanted a diagram for the Sawtron KG108 prg Cable
& How to reset the Processor in the kg108

Skinny


> Message: 1
>    Date: Thu, 11 May 2000 01:22:57 PDT
>    From: "Nick K" <nickv8@...>
> Subject: Tait 2020 cable info
>
> Hi all
>      Does anybody have any info on the Tait 2020 programming cable,are any
> other cables compatible with this unit? eg. PRM80,Sawtron,Icom etc.
>                                     Thanks in advance
>                                      Nick.

Nick K wrote:

Hi all
     Does anybody have any info on the Tait 2020 programming cable,are any
other cables compatible with this unit? eg. PRM80,Sawtron,Icom etc.
                                    Thanks in advance
 

Denis McKay

Anyone able to give me any programming information for the Tait T500
series radio's?

Regards
Paul

What Tait software do you require? Only the 2020 or others as well
Regards
Paul

Skinny wrote:

> Further to this
> Is there any software around for the units
> or do you have to manualy Hex edit the files.
> also wanted a diagram for the Sawtron KG108 prg Cable
> & How to reset the Processor in the kg108
>
> Skinny
>
> > Message: 1
> >    Date: Thu, 11 May 2000 01:22:57 PDT
> >    From: "Nick K" <nickv8@...>
> > Subject: Tait 2020 cable info
> >
> > Hi all
> >      Does anybody have any info on the Tait 2020 programming cable,are any
> > other cables compatible with this unit? eg. PRM80,Sawtron,Icom etc.
> >                                     Thanks in advance
> >                                      Nick.
>
> ------------------------------------------------------------------------
> Double your manufacturer's warranty on all computers,
> home appliances, and electronics AND win up to $500
> towards your purchase!
> http://click.egroups.com/1/3749/4/_/638173/_/958038261/
> ------------------------------------------------------------------------
>
> Community email addresses:
>   Post message: radio-programming@onelist.com
>   Subscribe:    radio-programming-subscribe@onelist.com
>   Unsubscribe:  radio-programming-unsubscribe@onelist.com
>   List owner:   radio-programming-owner@onelist.com
>
> Shortcut URL to this page:
>   http://www.onelist.com/community/radio-programming

I am in need of programming information for a Midland 70-165-16B VHF
handheld. Also need programming interface schematic.

Thanks in advance!

Craig Clark
http://w3.pca.net/~cpclark

Hi all,

I have a Motorola GP300 5 tone hand held that when attached to the rib box for
programming comes up with the error 'Radio Checksum Error 4' The radio is
unusable at this time.

Does anyone know how to reset this radio so that it can be reprogrammed again
or is it a trip to Motorola?




--
Christine Sweetnam

Email at chrisrs@...

Sent on 14/05/00
I take no responsibility for the following Tag Line. It is randomly generated.
__________________________________________________________
Politics: Poli (many) - tics (blood sucking parasites)

You might choose a GP-300 from your archives and try cloning this
radio.  Sometimes this works, sometimes not.

JR Hunt
Pro-Comm Systems

Christine Sweetnam wrote:

> Hi all,
>
> I have a Motorola GP300 5 tone hand held that when attached to the rib
> box for
> programming comes up with the error 'Radio Checksum Error 4' The radio
> is
> unusable at this time.
>
> Does anyone know how to reset this radio so that it can be
> reprogrammed again
> or is it a trip to Motorola?
>
>
>
>
>

On Sat, 13 May 2000 10:06:02 -0500, You wrote:

>You might choose a GP-300 from your archives and try cloning this
>radio.  Sometimes this works, sometimes not.
>
>JR Hunt
>Pro-Comm Systems
>


Just gave that ago and it worked. Thank you, you saved me from a sleepless
night.


--
Christine Sweetnam

Email at chrisrs@...

Sent on 14/05/00
I take no responsibility for the following Tag Line. It is randomly generated.
__________________________________________________________
A baby sitter is a teenager acting like an adult
  while the adults are out acting like teenagers.

Could anyone point me in the direction on the net where I could find the
service manual for the Tait 2020 Series II or any other extra info?

Regards
Rick

Paul,

if your in Perth, near a fax, or on Packet let me know and I'll see if
someone I know can get you the instructions.

Cheers
Richard VK6TT

To Richard (and all the other replies)

Many thanks to all for your quick responses.
I received about six copies of the required program information.

Once again, many thanks to everyone
Regards

Paul

RJBurden wrote:

> Paul,
>
> if your in Perth, near a fax, or on Packet let me know and I'll see if
> someone I know can get you the instructions.
>
> Cheers
> Richard VK6TT
>
> ------------------------------------------------------------------------
> Make music with anyone, anywhere, through FREE Internet
> recording studio software. FREE software download!
> http://click.egroups.com/1/3729/4/_/638173/_/958303504/
> ------------------------------------------------------------------------
>
> Community email addresses:
>   Post message: radio-programming@onelist.com
>   Subscribe:    radio-programming-subscribe@onelist.com
>   Unsubscribe:  radio-programming-unsubscribe@onelist.com
>   List owner:   radio-programming-owner@onelist.com
>
> Shortcut URL to this page:
>   http://www.onelist.com/community/radio-programming

I'm looking for a schematic to build an interface to
program the TAIT 2010 radio. I also need the pinout of
the microphone connector. Any help would be
appreciated.


              Regards de Bruno VE2VK/KD1XG.

__________________________________________________
Do You Yahoo!?
Send instant messages & get email alerts with Yahoo! Messenger.
http://im.yahoo.com/

Bruno Bouliane wrote:

I'm looking for a schematic to build an interface to
program the TAIT 2010 radio. I also need the pinout of
the microphone connector. Any help would be
appreciated.

Denis VK2DMR

OK here is the pinout for the Tait 2000 series radios.
Microphone: pin 1 Vcc+
             pin 2 Txd
             pin 3 Ptt
             pin 4 Mic
             pin 5 Gnd
             pin 6 Rxd

          Bruno VE2VK.
--- vk2dmr <vk2dmr@...> wrote:
>
>
> Bruno Bouliane wrote:
>
> > I'm looking for a schematic to build an interface
> to
> > program the TAIT 2010 radio. I also need the
> pinout of
> > the microphone connector. Any help would be
> > appreciated.
>
> I would appreciate the microphone pinout
> informations as well, guys.
>
> Denis VK2DMR
>


__________________________________________________
Do You Yahoo!?
Send instant messages & get email alerts with Yahoo! Messenger.
http://im.yahoo.com/

Further to my previous requests

Is there any difference in the diode matrix programming between a T530
and a T535?

I am currently working on a couple that are experiencing TX/RX problems
(appear slighlty off freq) and the diode matrix is different between the
radio's.

Regards
Paul

Does anyone have, or know where I can get programing software for the
Philips PRM8020?

Also, is the programing cable for the PRM8040 the same as the cable
used for the PRM8020?

Thanks,

Matt.

Hi all,
       Can anyone please help me with the software for the TK 370. Also does
anyone have a schematic of the diagram for the programming cable.
                                        Thanks in advance
                                           Nick.


                           NICKS RADIO SOFTWARE
                      http://members.xoom.com/nickv8/

________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com