Hello Brian Thanks for the reply. Indeed the fuse was blown and the on/off switch arced when I replaced the fuse, so I have bought a new one from Maplin and...
I got my new MOF router out for the first time today. http://tinyurl.com/dzoemr The problem was to deepen the rabbet in a ready-made picture frame by 1mm. The...
Hi I received the Proxxon FET tablesaw about a week ago and I have a few comments ! Plusses: Higher fence Micro adjustment (That's why I bought it) Minuses: ...
Thanks for that Niels. I was considering Upgrading to the FET because the blade isn't parallel to the fence on my FKS/E. Oh dear. Maybe I'd better just upgrade...
Just a follow up. I got an email from Proxxon. They will replace my Tablesaw FET free of charge. Proxxon told me that my version was from the first production...
Thanks. Back to my dilemma then. The FET looks very good on paper while being cheaper, and I'm surprised the fixed-speed motor is noisier. David ... From:...
Yesterday I received the replacement saw from Proxxon. I found it in the garage just before bedtime :-) Early up to unpack and test. Visual inspection shows no...
I've spotted advertising for the new GE70 engraving attachment for the MF70 mill: http://proxxondirect.com/site/cat/_c6/27102 Has anyone tried it for profile...
Hi David The MF-70 is very small. XYZ travel is 134mm x 46mm x 80mm. The engraving attachment does not have a coupling to the z-axis like on a real engraving...
I have just joined the group since I bought a lathe 2 days ago. It was completely disaasembled. It seems that some parts are missing, the most important one...
Having re-read my post I think I should clarify that what I need is a key for the spindle chuck, not for a drill chuck. I just hope that there may be a drill...
well, I guess this group is not very active. Anyway, the guy who sold the lathe to me found the chuck key so all is well except that the speed potentiometer...
I googled and never found any tips or tricks for the micro bandsaw Here's a few I came up with Loose miter gauge in slot, well after contacting proxxon and...
I have a couple of older Proxxon 12V tools, similar to current production but not quite the same. One is the little jigsaw. It's very neat for small jobs where...
Ok had a bit more time to fix the issues, To take up some of the up/down freeplay on the miter gauge in the T slot I just used the center punch on the sides...
Hello everyone, I am new to this group. Just bought a Microlux table saw and would like to hear from those with experience working with one of these machines,...
Hi Adi The Proxxon version (FKS/E) of the Microlux table saw has been the workhorse in my shop for the last 10 years without any problems. The tablesaw has...
Niels, thank you for the repply. Is good to know that the table saw is of good quality. I noticed, to my surprise, that it is made in Japan, not China. I...
Terry, thanks for the advice. That is what a thought about the dust damaging the motor. I will connect a small vac, that I have in my shop, every time I use...
Hi Adi Don't worry about saw-dust. As I wrote earlier I clean my tablesaw when the inside is full and it has never been a problem. I don't know if this group...
The fan you can see partialy covered with sawdust is to keep the motor cool?? so what is the point having a vac-- hoover take off point if you'r not going to...
I can see that too but I don't worry. I have used that saw for about 10 years with no troubles. Sometimes it is so filled with sawdust that the sawblade throws...
Hello everyone, thanks for all the help and advices on the table saw. Best regards, Adi ======================================= Please note: message attached ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
