Hi Joel, Since you go into Tx, be ready to have a supported audio card. There are many that do not go this way but they miss a lot and most likely could be...
Joel, Christos is all too modest concerning "supported" cards to be used for PSDR-IQ. His USB2SDR is fully a supported card. It has better latency that either...
My onboard RealTek soundcard just died in my Toshiba Windows Vista laptop. Please,any suggestions on a USB soundcard that will work on Vista? Using an Ensemble...
Windows Vista suggests an older laptop. Windows treats sound in a very extravagant way using a lot of resources. This causes latency problems. The "card" in...
Gary, I use the iMic USB sound card on my XP machine, both ports work fine in XP. The Windows 7 32 Bit PC I have works with the iMic stereo Mic from the...
Creative has the refurbed Soundblaster XFi 5.1 pro on their web site for $34.99 with free shipping. I bought one and am very happy with it on WinXP. John -...
Please note: That in order to transmit and receive/TX external audio "mike/SPKR" either 2 sound cards are needed or a 4in 4 out card. If the internal card has...
Hi Christos I finally got the new ATTiny85 installed with V15.15 firmware. Now it works OK with PowerSDR V2.4.4 X2 version giving the correct receive frequency...
Hi Christos Thanks for the link. Interestingly, I had already worked that out for myself, so I also get the correct indications on the tuning instead of "out...
Hi, The BandText section of the XML file only affects the display, it doesn't allow to transmit in out-of-band frequencies. This is hard coded in the program...
Hi Ignacio and Christos Thank you - I set up the XVTR page to use button 3 on VHF 70.0 to 70.5 with zero IF. Works a treat. I should have guessed that it might...
Hello, my name is Martin, DM4IM. I m new to this group. Please push me in the right direction: I use a SI570 based FA-SDR by DL2EWN, my Computer runs Win7...
I have the same sound card. I use the Emu 0202 for decoding receive only. Then I use my onboard sound card for the transmit. I've found that most of the...
Martin, What you mention as functionality that is not working is because you do not use a 'supported' card. PSDR version 2.x for the homebrew is only the 2.4.4...
Christos, thanks so far. I went to 2.44 for homebrew rigs. Seems to solve some of the problems. Are there supported cards with 192khz sample rate? I would hate...
I've completed my softrock Ensemble RXTX. I've been playing with it using v. 1.9.x.x of PowerSDR and have been advised to move up to 2.4.4. By the way I'm sing...
Read as available on this site if you look: http://groups.yahoo.com/group/powersdr-iq/message/2765 The USB2SDR is a 192KHz card. Sound cards using windoze...
Hello, is there a way to start up PowerSDR without the need to click on "USE SDR1000", e.g. a parameter... -- Ohne CW ist es nur CB.. 73, Martin DM4iM...
I wonder was the USB2SDR designed to fit a particular enclosure. Or has anyone any ideas concerning a screened enclosure for it. Best Regards 73 Eric VK5ZAG...
Hi Eric, I guess you already have seen this folder -> http://groups.yahoo.com/group/powersdr-iq/files/USB2SDR%20Mechanical/ with mechanical details. The cards...
Hello, I am new to this group, but not new to the SDR software experience. I have been using PowerSDR/IF Stage, a SoftRock, and an EMU-0202 to run my TS-940S...
Joe, i did the same. I went from a K3 with LPPan and E-MU 0202 using PSDR IF Stage to a SI570 based FA-SDR. I use the same hardware, computer, e-mu etc. You...
Hi Martin, Thanks for your comments. In an email message with Christos, he explained to me that PowerSDR-IQ was not designed to be used as an "IF Reader", and...
Hi all have followed all the steps in setting up the kx3 with psdr, using the pdf instructions. I am finding that the if a station is on 18.1450 usb running...
Nope, you didnt follwed all the steps. Look again at the RX SHFT (which is a locked menu item) and bear in mind also that it is band-specific so it has to be...
I think that perhaps if you look at the bottom Right corner of PSDR you will see a window for the CW offset, this may be causing you difference in tuning. I...
