I have tried and tried to have the Receive and Transmit Primary Sound Card Setup drop down boxes populated instead of grayed out. Only the Input, Output, and...
2743
tony_g3ovh
Feb 3, 2013 10:02 pm
Hi Christos I see you have just posted "PowerSDRv2.4.4_for_Homemade_Rigs_Div2.zip". I am presuming that this is the awaited program for the UHFSDR divide by 2...
2744
sv1eia
Feb 3, 2013 10:07 pm
There is no separate X 2 configuration. That setup is exclusively for those with ATTiny controlled Si570 on UHFSDRs and has manual VFO up to 999MHz....
2745
ericwd9
Feb 4, 2013 7:35 am
You will need to indicate what version of PSDR you are using? you will need to indicate what "sound card" you are using? If you have a "approved"; sound card...
2746
w8du_arnie
Feb 4, 2013 7:36 am
Hello all! I have PSDR 2.4.4 working fb with my KX3. My question is how to automatically mute PSDR in transmit? Does anyone have any ideas of what the setup...
2747
sv1eia
Feb 4, 2013 8:24 am
Hi Arnie, I guess you do not use what is specified on step 5 of the instructions. Read that steap once more. 73, Christos SV1EIA...
2748
Arnie
w8du_arnie
Feb 5, 2013 7:34 am
Thank you Christos, but I don't understand. Step 5 says to install a supported card, D44 or FA66. Does this mean if I don't have one of those cards, the...
2749
sv1eia
Feb 5, 2013 7:46 am
Arnie, Other sound devices than those could behave differently, due to their diversity of controls, and they are not controlled efficiently so some functions...
2750
Arnie
w8du_arnie
Feb 5, 2013 1:49 pm
It seems like the KX3 is outputting a I/Q signal to PSDR even on transmit. I am hoping there is a way to mute that signal. I will post this question on the KX3...
2751
sv1eia
Feb 5, 2013 1:52 pm
That is strange. I didnt have that in my local setup. Make sure that there is no other mic connected to your audio card, it looks to me that the problem has to...
2752
chris
oz1bxn
Feb 19, 2013 10:44 am
Hello How is the timing/sequencing working in pwrsdr IQ? This it important for QRO PA relays , especially in CW mode. I am particular interested in version...
2753
kaplanjo
Feb 19, 2013 6:26 pm
Hi Christos, First of all, thank you for providing the software and set of steps for configuring it. I have followed the steps and have my KX3 working with the...
2754
sv1eia
Feb 19, 2013 6:28 pm
Hi Jon, Usually that happens when you didnt manage to have the Bi-directional setup. The one that requires the setup of COM ports. Make sure that you have...
2755
kaplanjo
Feb 19, 2013 8:34 pm
Hi Christos, Thanks for the reply. I had VSP running. I deleted all of the ports, did a reboot and everything works now. Not sure if that was the problem...
2756
sv1eia
Feb 19, 2013 8:42 pm
Jon, Nice to see that its working ok. As you understand we are in uncharted waters here so some experimentation is required for setting up the addition of HRD,...
2757
Vittorio Bruni
vittorio.bruni
Feb 19, 2013 10:27 pm
Hi Christos, I have an RTX Ensemble SDR of Tony Parks (KB9YIG). I hope that you can resolve my problem. The system receives but it doesn't go to transmission;...
2758
kaplanjo
Feb 19, 2013 10:28 pm
Christos, I will give it a try and report my findings. Quick question. How does Com0Com know how to get to the KX3 USB port? The reason I ask is that I was...
2759
sv1eia
Feb 19, 2013 10:42 pm
Jon, The application scans the available COMxx ports and sends a query, on the one that a valid CAT KX3 response comes, then it uses it. Note that its the...
2760
sv1eia
Feb 19, 2013 10:52 pm
Hi Vittorio, It looks to me that a more appropriate place to put this question is the softrock40 group. As a suggestion, first make sure that your board and...
2761
kaplanjo
Feb 20, 2013 7:06 am
I spoke too soon. The rig and PSDR now communicate but I cannot hear signals on the rig on the same frequency as the PSDR. It seems like they are a few KCs...
2762
sv1eia
Feb 20, 2013 7:13 am
Have you set on KX3 "RX SHFT to 8KHz for all bands.." that is a 'per band' setting. Also, it looks to me that you still have not set the Bi-Directional COM...
2763
joelweder
Feb 24, 2013 10:05 pm
Hello all, I have recently finished building my Softrock and have been doing some basic testing of transmit functionality. Rocky isn't working well for me as I...
2764
sv1eia
Mar 4, 2013 10:20 am
Hi Joel, Since you go into Tx, be ready to have a supported audio card. There are many that do not go this way but they miss a lot and most likely could be...
2765
ericwd9
Mar 5, 2013 1:10 pm
Joel, Christos is all too modest concerning "supported" cards to be used for PSDR-IQ. His USB2SDR is fully a supported card. It has better latency that either...
2766
kc9ee
Mar 7, 2013 10:48 am
My onboard RealTek soundcard just died in my Toshiba Windows Vista laptop. Please,any suggestions on a USB soundcard that will work on Vista? Using an Ensemble...
2767
ericwd9
Mar 8, 2013 10:59 am
Windows Vista suggests an older laptop. Windows treats sound in a very extravagant way using a lot of resources. This causes latency problems. The "card" in...
2768
bxyza
bill.bathgate
Mar 8, 2013 7:04 pm
Gary, I use the iMic USB sound card on my XP machine, both ports work fine in XP. The Windows 7 32 Bit PC I have works with the iMic stereo Mic from the...
2769
John Williams
jswillms
Mar 8, 2013 9:59 pm
Creative has the refurbed Soundblaster XFi 5.1 pro on their web site for $34.99 with free shipping. I bought one and am very happy with it on WinXP. John -...
2770
ericwd9
Mar 9, 2013 12:05 am
Please note: That in order to transmit and receive/TX external audio "mike/SPKR" either 2 sound cards are needed or a 4in 4 out card. If the internal card has...
2771
tony_g3ovh
Mar 9, 2013 10:05 pm
Hi Christos I finally got the new ATTiny85 installed with V15.15 firmware. Now it works OK with PowerSDR V2.4.4 X2 version giving the correct receive frequency...
