A successful reception of SAQ's transmission in Grimeton at 24-12-2012 has been made in Athens, Greece. A 5 meter vertical wire was used as the antenna ,...
Hello, Recently I strarted to use PSDR-IQ insted of Rocky for my Softrock 6.3. I made some CW QSO with built in iamnic keyer and it works fine. Today I tested...
Thanks to everyone on this reflector I got my SoftRock RX Ensemble II working with version 4.4.4 of PowerSDR OK. But on my display screen the VFO frequency...
This message started off as a request for help, but at the end I found the solution, so I am still sending it in case others have similar problems: I am using...
Hi, I've most likely missed this somewhere on the group but can anybody please tell me, will PowerSDR V 2.4.4 or Vi.19.3.15 run under Window 8 64 bit?. Thanks...
Hello friends! I assembled transceiver for the range of 10-12-15M. There is also a desire to work for Ci-Bi 27MHz. However, the program blocks the lower...
Could powersdr somehow be setup to tune both a softrock ensemble rx and also at the same time tune a radio via CAT or HRD to the same frequency and so they...
Hello all, I have just acquired an old IC-735 from a hamfest. It has no dsp, nor does it have the narrow CW filter installed. The built-in selectivity is from...
I have a USB2SDR in as-new condition excess to my needs. $200 plus shipping US only. Please contact me off list at my QRZ.com email address. Thanks Fletch ...
Hi Christos et al, Are there any plans to resurrect the facility to unlock the Tx frequency range, as on the V1.12 version? The new 2.4.4 does work better for...
Wow!! The installation went smooth as silk. Thank You Christos for a superb job. The configuration here is the Ensemble RxTx for 40/30/20 and a Delta 44...
I have just uninstalled my previous working version of PSDR and have installed the latest patch for ver 2.4.4 I find no support for the USB2SDR is this...
The latest version works well but I had a issue about the paddle keying. "Dot" is OK but the"Dash" is not respond very often. So I asked to Christos then he...
I have instaled this new software,every thing works very well apart from i can't get cw paddle to work..Keyer in software works ok..Useing win7/64 delta 44...
I'm trying to get the 2.4 software to work and keep getting file not found error. pal.dll I've downloaded the skins but I'm unsure where they are installed to....
I run digital modes with a pair of softrocks. I need to know if PowerSDR, MMTTY, WSPR, JT65-HF, and Digipan will work with Windows 7 or Windows 8. My old...
I am running the RXTX with a M-Audio Firewire Sound card and PSDR Ver 1.19.3.15. I have not been able to figure out how to configure another sound card to...
I use an output level from the sound card of +4dBu for my interface to the MOBO. This is needed to obtain a 5W output. What I have noticed is that PSDR-IQ...
Hi Christos Thanks again for your advice. I posted some pictures under the name PowerSDR Installation Errors. I have installed the USBtoI2C drivers, they are...
Hi Guys I'm new to PowerSDR-IQ, I was using HDSDR. now I installed PowerSDR ver 1.19.3.15 but I got a nasty error everytime I tried to open the program. I'm...
I want to run two SDR radios from one iteration of PowerSDR. Only one radio will be in transmit at a time. Each SDR will run a transverter for satellite...
Has anyone successfully married up a KX3 and PSDR-IQ? NaP3 does a nice job, but just working with the I and Q data, PowerSDR seems a little cleaner. What seems...
Christos, After looking through the old mail I'm still confused about PSDR-I/Q V 1.19 preview I need divide by 2 for the UHFSDR do I need to use a different...
I have just installed PowerSDR v1.19.3.15 and have been using it for a couple of hours. I am using it with RXTX 6.3 I2C Si570 Windows 7 x32. Up to now I...
