... Jim: It's possible and not too difficult yo do. I assume you have a JET mini VS? Look carefully at the bed of your lathe and you will find a plate over a...
Hey Everyone, I just joined the group, and wanted to step up on the box and start off with a big Thank You to the Armed Forces and Veterans of all Nations who...
Folks, For those planning on participating in the Penturners Rendezvous, either in person or via the pen display, the time is growing short. Online Rendezvous...
... it ... wood ... Mike.... I think I had the same problem that you have or had. Last August I bought a Jet lathe from Woodcraft. All was well for a few...
thank you for letting me join this group. i am just starting out in woodturning. am a wood carver and wood burner. i have a toy lathe a dremel moto-tool. but...
Randy, Not to be picky, but you'd have to wire the two switches in parallel not series in order to have both work independently of each other. If they are...
ER 32 even better. What is the connection to Beall? Is this a penturner thing? This system has been around for many, many years, since the ES/ER collets were...
In a message dated 5/1/2008 9:41:29 A.M. US Mountain Standard Time, bill@... writes: If they are wired in series, you will have to turn both of them...
... Your first statement is correct; but it is no big deal because you just leave the switch on the controller in the on position all of the time and use only...
... Bill: You are correct and not picky. I am aware of the difference between wiring in series and parallel. Only thing that got you off track is I did not...
Thank you so much Bob for understanding I am here in pain because of the situation Diane have pen blanks right now in her house in California I keep forwarding...
But a chuck for our wood lathe to hold the collets hasn't. J.R. Beall (Beall Tool Company) started making the chucks for our wood lathes to hold the ER32...
I want to thank all of you for your help and advice. I was telling my wife on the drive home from work about how helpful this group has been and everyone has...
Hello Dave, send me your address, and I send you a few different pen blacks to try out. For me it's what ever strike my fancy, I like most all woods , ...
Don; I'm pretty sure you already know this. You can get ER32 or ER25 collet holders with both MT3 and MT2 tapers (respectively) on them. You should always...
... It does not. Each collet has a grip range of 1mm or .040", down from the nominal size ... Well, this is not a complete set either... a 'complete set' has...
Not exactly, As has been mentioned, these collet holders come in a variety of sizes for lathe mounting and mill mounting. Morse taper is one type. I have a...
I've been watching this thread on collet chucks. I have one that screws onto the threads on the headstock. When I was looking for a collet chuck, I went to a...
Dennis; I have dealt with these folks in Cal and always had good service. They do metal mini-lathes in the 7x category, but applicable to other sizes too. ...
Neither Sherline nor Beall invented the ER type collets or collet system. Anybody with machining capability can machine an adapter like Beall designed. You...
... The PSI collet chuck comes with 5 ER32 collets just like the Beall The collets go from 1/4" to 3/4" in 1/8" increments. If you are a pencrafter, the...
... Rich: I.m curious. Why do you need collets in 1/2mm increments? Since the ER32 collets have a grip range of 1mm and they come in 1mm increments, 1/2mm ...
Don't knock the cross grain untill you've turned them. Will be a very interesting pen.... I've done some Oak that way, with great satisfaction.... Regards.. ...
I don't *NEED* them. :-) But if you've worked with collets you'll know there is a convenience in having an exact or close to that fit. The 1/2mm sizes were...
... Anothe collet system that Ralph and others have failed to mention is the Morse taper collet. This is a collet that fits directly into the lathe spindle...
... Yeah, that is very true. Thanks. If you have a rod that is at the small end of the grip range, you really have th crank down on the collar to get a good...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
