Hello men, I found about about a big oak tree that a lady needs to have taken down and you can have the wood. Sounds like it would make some nice big bowl...
I believe that she would like for someone to take it down for her and then you can have the wood, but you could call her and ask her. She might would be...
Hello PWT, I was wondering if anyone got lucky with some falling trees with all the high winds. The EWN (emergency wood network) is ready to help! Well, as...
HI I will not be able to make the meeting Saturday but would like to pay my dues. Is there a way to pay with out being there? Richard Green ... From:...
Hello Richard, Yes there is. I have attached the membership form (it has my address on it) in Word format. If you have any problems opening just let me know...
203
BARBARA KLEMME
cklemme@...
Jan 9, 2009 1:20 pm
Greg, If you elect to conduct PWT business on the yahoo forum, I'll request to be removed from the list. That kind of mail could quickly get out of control...
I plan to attend the Pen meeting. (I have some questions for the pros ;-) -rick ________________________________ From: gprevost0003 <gprevost@...> To:...
Hi Greg, Would you please remove me from this goup? Thanks Richard ... From: Greg Prevost To: palmettowoodturners@yahoogroups.com Sent: Friday, January 09,...
I purchased a new grinder from Harbor Freight and one of the wheels is vibrating a lot more then the other. Is there any secrets here I need to know about or...
207
cklemme
cklemme@...
Jan 12, 2009 1:28 am
Greg, Sometimes just truing it up with a grinding wheel dresser will do the trick. That's a grinding tool that is impregnated with diamond dust. Can be...
208
benpen465@...
Jan 12, 2009 1:59 am
All new or remounted wheels need to be dressed or trued again with a diamond dressing tool. That usually works. Wheels need to be cleaned and or dressed at...
209
Michael Rabkin
mfrdds@...
Jan 12, 2009 1:59 pm
Hi Greg....I sent a reply to the issue, but I am not familiar with the yahoo deal so I will reiterate.....average to inexpensive grinders are usuall high speed...
Hi Greg, A bad wheel cannot be made good. Diamond grinding will not make it right, it will only make it smaller. Please don't inhale the dust or we'll have to...
I would not replace the wheel. I have an 80 and a 120 grit and wish I had 60 and 80. When I want to remove metal, I want it to be fast, therefore the 60 is...
I just got the Sharp Fast system which looks pretty good but I have not yet installed until I am happy with the wheels. I haven't tried switching sides, I may...
Greg's recent post about grinding wheels reminded me of a question to ask. I know that fast grinding will heat up and "burn" carbon steel tools. I have heard...
Well, I found this very interesting thread about it. http://yarchive.net/metal/hss_grinding.html Since the temper point of HHS is 1100 degrees (a dull red...
216
ROGER WRIGHT
rahawright@...
Jan 12, 2009 10:08 pm
Greg, Change wheel sides. If same side is wobbling then grinder has a bent shaft. If not then true up wheel as suggested. Roger...
217
Nick Leoncavallo
nickkathy45@...
Jan 12, 2009 10:08 pm
Check out this web site on knife make and hardening of steel. Especially look at the 4th chart called "tempering" Note that M2 tool steel (one of the HSS's),...
Hi Rick, This is absolutely not true. Fast grinding is not a problem. Heavy pressure is a problem. I have 'fast ground' gouges. Works fine if: 1) You apply an...
RICK: I believe that Richard P. has it right. Good sharpening can be accomplished using either Fast or Slow speed grinders. it's the gentle touch that produces...
221
Nick Leoncavallo
nickkathy45@...
Jan 13, 2009 9:56 pm
Great article lots of info. Nick L....
222
joenat56@...
Jan 13, 2009 10:36 pm
Greg, Please take me off this forum. It generates too many emails. Thanks for the good job you are doing as secretary/treasurer. I did it for 3 1/2 years...
223
Luther Vann
vanwoodturner@...
Jan 14, 2009 1:10 am
The tempering points are not the same on all HSS tooling --some are low as 400 degrees which is a light straw color. So do not turn the tool blue. The high...
It is probably possible to stay on the list and not get the emails. I'd like to get the emails, but don't, so there must be a way to "uncheck" something so...
Per his request, I already removed him so he did not see your email. But yes, there is several settings to control email if it is more then you like. From...
GREG: I tend to agree with the direction that Jay is suggesting. This can be a good forum, but it should be in a category where the individuals involved select...
