Dear all, On page 7, Table 3, Pin 9 description says: "ADC5 input/Power Relay". On the schematics however port X1 pin 9 is wired to ADC8 while ADC5 is wired to...
Dear all, Once I have closed the enclosure of the OT+, is it possible to re-open it again without compromising its structural integrity? Any tools needed? The...
Dear all, My Huber is aging (well but still) and even though there is a decent number of PC-pluggable WX stations out there I'd like to know in your experience...
Yes, and in fact I think I posted a video on how to do it somewhere. A small screwdriver will do it - just push in on the tabs on one side and gently pop it...
had a strange experience trying to use thevan icon overlaid with a number'3'. I set the overlay character as a 3, andselected thevan icon character, "v"....
There is some weird thing about Base91 and overlays... I know I ran into this recently. Thought I'd fixed it, but I don't remember exactly what it was. I'll...
Dear all, What PTT signal is asserted/driven by the OT+? PTT Output (X1-pin3) or PTT Input (X1-pin8)? Also what are the voltage values asserted by the OT+...
I'm not going to say it works until someone's actually tested it and verified that it really does. If it does work, let me know and I'll put a note in the...
It sounds as if the OT may have the same buffer issue that Kenwood Tasco TNCs have. Winlink FAQ entry Q3000 (http://www.winlink.org/faq) suggests that you need...
While connected to service monitor, EXACTLY how do I set the deviation? Do I check each tone separately or combined? the 2200 tone is 1khz higher in...
I believe the buffer problem on the Tasco TNCs is worse, in that they actually crash when the buffer is exceeded. At least the T2 will just drop frames. Scott...
I have a t-135 that works very well. But my computer (3.0ghz Gateway) will act up and go offline and my cable modem would require rebooting. This would happen...
This started as a Tracker2 project, but I'm thinking about doing it with the OpenTracker+ first - it'd be faster to put into production, at least in kit form. ...
One word: One wire. Okay, that's two, but the point is extensibility. You could avoid putting in too many relays, and just add extra software to handle ...
Hello Scott. Some suggestions: - Make at least a couple of the analog inputs (or all, configurable?) accept PT-100 or PT-1000 temperature sensors; they are...
... And 48 VDC is Power over Ethernet standard, if it's going to have ethernet. But I'm jumping to conclusions here aren't I? It would be really neat if it had...
... I'll take a look at those. ... Definitely not going to happen on the T2. I've got an ARM7 board here that'd do it, but that's many months away still. And...
I may try to come up with a DIN rail clip for the transceiver. For now, though, it's going to be separate. It's coming along, but the latest batch of samples...
"It would be really neat if it had a portable data transceiver and GPS receiver built in too. I hope that project is coming along nicely." I second that,...
gps would be great, just the reciever inside with a antenna connector to externally mount the gps antenna. i also like having connectors for the one wire...
For power, we use these in a number of projects at work: http://www.linear.com/pc/productDetail.jsp?navId=H0,C1,C1003,C1042,C1032,C1082,P8651 You can throw...
Yeah, but it's a lot of external components, at least for a kit. I think there are some good low-power parts out there that don't need as many. Scott...
9600 baud on the on-air side? Never tried it, and it'd probably need to eliminate some other stuff to make room for the scrambler and filters. Scott...
I'd like my Yaesu FT-90 and OpenTracker+ to play together. Anybody done it? It seems fairly straightforward if the radio were to be dedicated to the OT+, but...
Dear All I have an opentracker The GPS is connected on the ground (black) red (Vin) and green (data) There is 5V on the serial port. The red light keeps on...
It's finally happened - I'm out of OpenTracker 1 (not plus) MCUs, so until I find a new source (they've been out of production for more than a year) I don't...
