Carl - Your help files list using the LDG Model AT-11MP Tuner as External Tuner. It also works with the LDG RT-11 Remote Mounting Autotuner with the following...
... the ... Yes, it does but only if you have the type of noise the noise blanker is capable of removing. The noise generated by my wife's hair dryer motor is...
Thank you for the reply. I have tried the NB adjustment on every type of noise I can imagine, it seems to have NO effect what so ever. Not sure if perhaps I...
Run a hair dryer near your antenna so that you can hear the noise in the receiver. This type of noise here is removed pretty well with the NB slider. But I...
My experience is that the NB works well with the sort of "motor" noises, steady pulses, that Carl describes. Some, it takes out completely. Others it...
I had a lightning strike close by last week. As far as ham radio goes, it damaged my TS-2000, Jupiter, and an MFJ tuner. It also put out the computer I was...
The port speed of the Orion is 57600 baud, not 9600 baud. Look in your Orion manual for the correct settings for the serial port. Jim K4JAF Original...
Bill, I had a major strike here also in early August. I also had problems with computer control of the Orion after I repaired my station. The 56000 vs 9600...
Recently I have changed my operating procedurues where the last program I now shut down is N4PY's program. I have noticed the program will release the...
This has been fixed in version 2.25 of my Jupiter software. It was a problem with windows XP and my software. If you upgrade ($45), you will get the fix. ...
Hi Carl, after all the trials and tribulations we fround trying to use the K2. I m now off the K2 altogether. I stillwill keep it operable on the the IC...
Has anyone setup the microkeyer for the pegasus? I created the virtual com port but the pegasus was not listed in the radio dropdown list and my N4PY software...
I received the v225 from Carl and unzipped it. At first I couldn't get the program to open. As I was writing a post to that effect someone windows came up...
Gang - I could use a little guidance. I want to tune my Pegasus at 20 watts. I would like to click on AmTn to go up 5 and set the mode to CW. Then I would...
John, The AmTn control is for setting the drive power to an amplifier. It is not for just tuning. The idea is when you turn off the AmTn button, you have ...
Carl - That works just fine. I could also use the external tuner button, but that quits before the tuner (LDG AT-200) completes a full tuning routine. The...
Hi All - I have been using the SW for a few months now, but I am not a "Power- User" of all the functions and features. I'm using the SW with a Ten Tec Argo V...
Steve, When a memory is recalled, the portion of the code that sets the operating mode also sets the step size to whatever you have defined for your default ...
Hi Carl: I've found a strange problem which I can't seem to solve. When listening to my 480hx I can see that the output power is set to 200 watts. When I hit...
Hi Carl: I'm running 2.24 and do have the 480hx defined as the rig. I'm getting ready for Nov SS. I found when I use Writelog to key the rig, via cw or ssb, I...
I believe this was fixed in version 2.25. I just sent it to you again. 73, Carl Moreschi N4PY Franklinton, NC ... From: "Richard Thorne" <rmthorne@...> ...
Thanks Carl: My mistake, I saved your last note with 2.25 I just didn't install it. I'll do that shortly. Today will be the big remote contest test for me....
Hi Carl: I installed 2.25 but still have the same problem. But I did some more digging, and, how about this, I read the manual. I noted the tune function....
Hi Rich, You might want to rethink your tuning power level. The feature to have a low power level during the tune up might just save your equipment some day...
R,R Art. Not a problem for now as I don't have an amp in line. Rich - N5ZC ... From: Art Harding To: n4pysoftware@yahoogroups.com Sent: Saturday, November 05,...
Thanks Carl, Yes - you describe what I was experiencing. I was not savvy enough to figure out that the ManMd button would sort of over-ride or fix this while...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
