Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the n4pysoftware group. File :...
n4pysoftware@yahoogro...
Oct 1, 2008 12:59 pm
1186
I noticed after installation of V3.02 that now the frequency display resolution changes with the selection of frequency steps. This may be only a setting but...
The option is in "Preferences3" and is called "Round off Freq by Step size". Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 ... From:...
Is there anyway of getting to the filters below 300khz for the new Jupiter that just came out. Am very interested in this as I work primarely CW and rtty. N4PY...
You can right click on the 12 filter buttons and redefine them for any filter value you want. The filter selection goes down to 150 hertz. Carl Moreschi N4PY ...
I have intermittent connection between the program and the radio. Everything boots up fine and works normally (typically for 3-5 minutes) and then it loses...
I Have Ver 3.02 and my filters only go down to 300 Hz! I right click and that's as far as they go! Leon, N5PU Re: Filters You can right click on the 12 filter...
300hz. is the narrowest filter allowed by the Pegasus firmware. When they changed the firmware on the Jupiter to go to 150hz, they didn't do the same for the...
Carl, Do you have any software for Kenwood radios yet ? 73 don N5DLR ... From: hjohnc1999 To: n4pysoftware@yahoogroups.com Sent: Tuesday, November 04, 2008...
Kenwood TS-850, TS-950, TS-570, TS-870, TS-480, and TS-2000 are now supported according to Carl's web page. Mike NU4Q On Sun, 9 Nov 2008 08:27:35 -0600...
Mike could u send me carl's web page address 73 don n5dlr ... From: Michael Kallstrom To: n4pysoftware@yahoogroups.com Sent: Sunday, November 09, 2008 10:07 AM...
CARL, I received ur notice on renewel awhile back for my Pegusas, but i no longer have it, Now have the ken ts-570dg. How much do I need to send for the...
Hi Carl I hope you enjoyed your Thanksgiving ! I could use a little help , I was able to increase the size of the face of the radio on my 21 inch monitor but...
Hi Carl, I am using registered version 2.39 with my TT RX320D receiver. I know that your V3 series is now a real 32-bit application. I wonder that this also ...
Yes, the 32 bit versions will install in any folder or directory. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 ... From: "W6AFK"...
CARL WAS WONDERING IF YOU CAN SEND SOME IMFO ON WHAT YOU HAVE FOR THE NEW TEN TEC JUPITER ANY TRIAL VERSIONS I REALLY WOULD LIKE TO RUN IT WITH COMPUTOR...
Hi Carl. Please remove my above bad email from the N4PY yahoo group. I have been using a FlexRadio SDR1000 for a couple of years now and the software available...
You can do that yourself... Go to the main group page...near the TOP is EDIT MEMBERSHIP...select that then scroll to the bottom and select LEAVE GROUP....
WOW!!! I love the extended receive functions. I can now listen to many shortwave stations using the Orion direct or with true SAM using the LP-PAN. That's...
Carl, I tried to install 3.03 but I keep on getting the following error messages: (4 times) "ERROR_MOVEDATA - entry not found in the string table" Then the...
... wire ... It sounds like one of the typical Windows Vista glitches. Elsewise, I might suggest manually unzipping the file to a folder on the desktop and...
On December 1, I put out new versions for the Pegasus, Orion and Icom programs. The Pegasus program Version 3.03 which supports the Tentec RX series receivers,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
