Hi All One of my friends who also owns a 4000 called me up tonight and asked me if i knew how to set up a 4000 for PCM modulation in menu 4. He has set the ...
The Multiplex PCM encoding is proprietory to Multiplex, as other PCM schemes are to other manufacturers. I suspect that a Multiplex PCM reciever is not being...
Hi Veronica It is an old MPX PCM receiver, and it works with his old 3030, as mentioned below. Are there anything else to be done but shifting to PCM...
Hi All Problem solved. I met with him today and we scanned his channel with my 4000 and there was a signal output. It turned out that when shifting to his old...
Mike, Made setting up a plane using mixers very understandable. It helped me figure out how to create some mixers for my use... Thanks for publishing all the...
Hi all sorry for taking up bandwidth, but if anyone knows Klaus Nierig (Kla- Ni@...), will they tell him to switch on his disfunctional email Rx (obviously...
Just wondering if anyone else has had the synthesized RF deck die in their Royal EVO? I have a 9 and my RF deck died today at the field. This is the second in...
Mine's in the shop for the 3rd time... ... From: Pete Cosky To: mpxradios@yahoogroups.com Sent: Monday, September 05, 2005 4:17 PM Subject: [mpxradios] EVO RF...
I've been hearing a few (handful) pilots that mentioned problems with their synth deck crapping out on them on RCGroups. I've owned mine since early this year...
Mine has died twice and both times were at power on not during flight. I'm curious to see what MPX will have to say. ... From: mpxradios@yahoogroups.com...
Hi folks, New here, used to listen to clubprofi. I'm from the Netherlands so excuse my spelling and grammar <http://www.rcuniverse.com/forum/image/s1.gif> ....
Hi Christian I think you're stuffed on this one. With two exceptions (see below), all mixer inputs drive all servos in the same sense. So for exaple with you...
Just wanted to update the list as to what I have found out. First let me say that MPX USA has GREAT customer service......I have a new RF on it's way to me. ...
Hello Mike, thank you! it's a bit of a bommer, and I thought it would be like that. Any way, I don't think the added value of tailerons combined with ailerons...
Hi Bob and Christiaan I spoke to soon! ... Bob, thanks for pointing out the solution - of course this works... Assign a separate mixer with Aileron-Tr and...
Mine went dead at power up as well, but they just had me send in the rf deck so at least it was a cheap shipment so ask if that is ok upon talking with tech...
... On all the various forums, I haven't seen one single crystal-RF deck failure report. Zippo. In contrast, there have been dozens of synth deck failure...
In a message dated 9/8/2005 10:37:07 P.M. Eastern Daylight Time, drela@... writes: I went the crystal route, and have never regretted it. Very prudent -...
I have a synth module and a crystal one as a backup. Have not had to use the crystal module yet. Maybe this is the secret to getting the synth module to work...
Hello, I have a crystal module, and never had any problem. Besides this, on the matter of the tailerons, I tested with the two mixers for the taileron (on for...
Has anybody tried using a lipoly battery in there 3030? I need a new battery and had the thought that lipoly's are quite a bit lighter than Nicad's/Nimh's,...
yes, I am using Lipo's in my 4000, works very well !! _____ Von: mpxradios@yahoogroups.com [mailto:mpxradios@yahoogroups.com] Im Auftrag von citrabia2000 ...
no, I don't regulate the voltage. I am using 4 2200mAh Lipos 2s 2p. _____ Von: mpxradios@yahoogroups.com [mailto:mpxradios@yahoogroups.com] Im Auftrag von...
I have a 4000 (Version 2 software) on 40Mhz with scanner and synth RF module. I also have a 35Mhz RF module as I fly as well as race boats. My question is does...
On my EVO9 with IPD receiver, all servos are waving when receiver turn on . However, I don't have this problem when I use a Futaba FM receiver w my EVO9....
You aren't using a 6v pack by any chance are you? I have had issues where a particularly hot pack will cause servo fluctuation with no input due to the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
