Guys I have a 1937 Lincoln type 37 coming in the near future .Aluminum Body ,steel fenders . The issue of using tools which I used on steel working . Do I have...
73036
Terry Thorne
oldgoaly
Jun 2, 2009 1:09 am
gordo, I got a web error "unknown" there is a little box that says my picture 007.jpg attached to your post. tt...
73037
Terry Thorne
oldgoaly
Jun 2, 2009 1:10 am
well just clicked on it again and it took me to yahoo and the picture. so???? it must be working.....tt...
73038
gordon bartlett
stingshp2001
Jun 2, 2009 2:06 am
AAAUUUWWWW ,TT GordonB ... From: Terry Thorne To: metalshapers@yahoogroups.com Sent: Monday, June 01, 2009 8:10 PM Subject: Re: [metalshapers]...
73039
oldgoaly
Jun 2, 2009 2:25 am
Gordo, hopefully Rick Mullin will chime in, but for a car that is 70 yrs old? and how does a tool pick up metal? a shrinking hammer? ok I can see it, but...
73040
Richard Ferguson
ka0dxm
Jun 2, 2009 2:35 am
A few comments: Your tools are steel; I don't think that anybody is working aluminum Audi bodies with titanium tools. I am ruthless about keeping abrasives for...
73041
gordon bartlett
stingshp2001
Jun 2, 2009 3:13 am
I normally scuff/buff my tools and then a wipe down ,it would be nice if thats all thats needed . I ;ll look through your Articles shortly . Thanks Richard . ...
73042
Ian
unklian
Jun 2, 2009 5:46 pm
Jim: Will you be accepting visitors this Friday ?...
73043
jim bailie
bailiecustoms
Jun 2, 2009 8:17 pm
Yes sir! any idea what time you'll be here. Jim Bailie ________________________________ From: Ian <unklian@...> To: metalshapers@yahoogroups.com Sent:...
73044
Gordon Bartlett
stingshp2001
Jun 3, 2009 12:15 am
Richard They say about the same as the M/Benz dealer here. Iron Particle contamination is the cause of the problem .M/Benz requires separate tools and location...
73045
Ian
unklian
Jun 3, 2009 12:25 am
I will be there later than I plan, probably between 12 and 2....
73046
jim bailie
bailiecustoms
Jun 3, 2009 12:45 am
see you then Jim Bailie ________________________________ From: Ian <unklian@...> To: metalshapers@yahoogroups.com Sent: Tuesday, June 2, 2009 8:25:34 PM ...
73047
bl55303@...
mnlars20032
Jun 3, 2009 2:16 am
The machine work on that car is just out of this world. Would like the chance to spend a couple hours looking. What are you guys doing...
73048
Kent White
kent@...
Jun 5, 2009 3:21 pm
Hi Gordon, I wrote an article in ABRN years ago about doing this kind of metal work. It was detailed and researched and, reasonable. In response there was...
73049
CGRAF
gaudeteforge
Jun 5, 2009 4:38 pm
I think tt asked how can a smooth faced hammer pick up iron contamination. Easily enough as the amount necessary to cause a problem is almost on the atomic...
73050
Kent White
kent@...
Jun 5, 2009 5:12 pm
If I remember correctly, stainless steel has a temper sufficiently high enough to "accept" steel particles from carbon steel wire brushes, hammers, dollys, and...
73051
gordon bartlett
stingshp2001
Jun 6, 2009 1:46 am
Kent I have the first and secound article's from ABRN in 1995 from my "Dark Days" of collison employment . I gleened a lot from when I first read them ,I'd...
73052
msaforum@...
themsaforums
Jun 7, 2009 9:01 pm
peter covell ( covelluk ) has posted a new message titled "Re: Peter Covell's English Wheel". Posted: Sun, June 7th, 2009 - 3:08PM Ive no plans to build them...
73053
msaforum@...
themsaforums
Jun 7, 2009 9:02 pm
peter covell ( covelluk ) has posted a new message titled "mechanical planishing hammer". Posted: Sun, June 7th, 2009 - 3:16PM Here is an alternative to an air...
73054
John Buchtenkirch
pettingellha...
Jun 8, 2009 6:09 pm
Here is an alternative to an air planishing hammer.The head was designed by Ben Van Berlo.I designed an built the rest of the machine Pete Pete, very...
73055
ptp80
Jun 9, 2009 2:45 am
Hi, No luck with P8 manual finding yet:( I contacted Pullmax Sweden to get manual, they forwarded me to Pullmax reseller in Finland... Reseller called me, but...
73056
gordon bartlett
stingshp2001
Jun 9, 2009 2:59 am
Pete Good looking Plannish Hammer. I 've heard goods things about head design .-GordonB ... From: John Buchtenkirch To: metalshapers@yahoogroups.com Sent:...
73057
oldgoaly
Jun 9, 2009 3:20 am
Pasi If you don't find a manual I can get you a P7 manual, Probably 60-75% is the same, I don't think my 1960 sales brochure has the P8 listed. email me at...
73058
John Buchtenkirch
pettingellha...
Jun 9, 2009 3:05 pm
I have run into these vises at swap meets for years but they were always beat up with broken or non-parallel jaws from people using them for heavy duty...
73059
Ian
unklian
Jun 9, 2009 3:35 pm
Never seen one like that, very cool. I used to have a Fitter's Vice, they have a quick release lever so you can open and close the vice quickly, without using...
73060
msaforum@...
themsaforums
Jun 10, 2009 9:45 pm
Chris Border ( 36anvil ) has posted a new message titled "Metalshapers in Oregon". Posted: Wed, June 10th, 2009 - 4:05PM Hello all, Just wondering if there are...
73061
oldgoaly
Jun 11, 2009 1:53 am
Lawerance Brand Chilled Lead Shot Made in USA. Taracorp Industries, Incorperated 1200 16TH Street Granite City, Illinois 62040 618-451-4400 I have no...
73062
John Buchtenkirch
pettingellha...
Jun 12, 2009 2:41 pm
I got the idea of mounting my Hossfeld bender on sort of a metal creeper from my friend's iron shop. I went one step further by mounting the bender on top of...
73063
Ian
unklian
Jun 12, 2009 5:10 pm
Can anyone recommend a GOOD board on Bladesmithing ?...
73064
gordon bartlett
stingshp2001
Jun 12, 2009 5:45 pm
Neat set-up John. I'm always looking for ways to add more tools to my already to small shop and that will help. GordonB ... From: John Buchtenkirch To:...
