Was told by the Southern area Tec Rep that they are NLA! He said the only hope was to find an old one on an old dealer's shelf, which is near impossible to...
if they are not available NOS then they could probably be fabricated fron Nylon or Delrin, 3/16 nylon 6/6 is available from USE-ENCO.com p/n 510-1599 for 34...
I have a service manual for the Snapper/Massey Ferguson 1600, 1650, and 1855 series garden tractors and mower attachments. I bought it from a dealer a couple...
Just purchased a MF 7 lawn tractor without a motor. First I am hoping someone can tell me when it was built. Serial No, 1590224604. Second I want to...
Wes you sound like a fine gentleman why dont i buy you a couple of feet and you make a couple of dozen i will give you a couple of beers (or $5) for one. ...
newlowell 54 MF-7 1590-224604 was built in 1971. Harold newlowell_54 <newlowell_54@...> wrote: Just purchased a MF 7 lawn tractor without a motor. First I...
MF 1450 with Sundstrand pump model 90-1165 LH, which port on the top of the pump supplies pressure? If sitting on the seat would it be the left or right? I...
Thanks. That was way too easy! I got the rod pulled, welded, and re- installed in about an hour. Before you posted, I had the left side of the tractor almost...
I have seen some pics posted of Tricycle front end on some MF tractors, does anyone have close up picutre view of the components. Would love to see how they...
I know this site is not geared towards the newer machines but I wanted to see if anyone knew the answer to this. I do have a 7, 8, 10, and 12 but also have a...
Scott Check the brakes, could be a peice of gravel in them. you could also block up the rear end so the tires are off the ground and put it in gear to help ...
... you won't get much from him cause i already seen it before and asked him for the details on it and his reply was he was afraid of the strength factor there...
... and the answer by everybody "in the know", was the stock hydro pump at the rear of the 1450 does not have the capacity to power a FEL. I did power my...
Hello, for those in need, I listed a steering wheel cap from an MF12 on ebay yesterday. It is in very good shape and is a no reserve auction. Here is the...
It is all about flow times preasure. I think your built in tractor pump should be ok, if you don't mind waiting for it sometimes. You may need a little bigger...
yes if you look in the photos it is still listed ... From: Gary To: masseyfergusongardentractors@yahoogroups.com Sent: Tuesday, September 05, 2006 1:53 PM ...
Speaking of these odd ball sort of things, Does anyone have the golf cart conversion for the MF 10 & 12? I've only seen it in the brochures. Gary in MN ... ...
Hi guys, I'm a new member. I've been reading some of the old messages and was wondering if anyone could tell me the year my MF8H was made. 1590508025 is the...
I mounted my snow blade last night just to check the fit. I wanted to make any adjustments/repairs before snow hits and it's 20 degrees below zero. Everything...
The mount holes are for a bracket thats used to center the plow. It keeps it centered and aligned when lifting. You can fab a simple bracket and use the holes...
Matt MF-8Hydro Serial # 1590-508025 was built in 1975. As for the trans oil the ops manual called for trans type A, Harold mjydrafter <matt.yoder@...>...
A guide mounts on the front frame of the tractor. It has two fingers that centers the c channel and a tall loop that holds a lift assist spring Steve ... From:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
