Its used to happen in Finland, due to all the ammo fired in the woods ... and we mill a LOT of wood. I think nr 2 exporter in the world after Canada or...
Thanks, Guys. Very informative. I have a three way lab supply. The DC output commons are isolated from the earth ground entering the cab on the AC side. They...
What would make the transformer "naturally float around ground" if neither leg is grounded? What you are describing(one leg at +35, one leg at -35" is a true...
hi I have a bunch 1923 10-20 ,fowler crawler, fieldmarshall,w6 I cant ... have ... tractor), a ... didn't ... to ... to ... JD with ... Barker ... have :) I ...
Hi, I like to use Suspend to Disk for shut off of the Mach3-Computer. After waking up the machine, there is no chargepump working. Any other Signal is ok, I...
Hello, I have just posted some pictures of my CNC Minilathe, they are in the John's <http://ph.groups.yahoo.com/group/mach1mach2cnc/photos/browse/d792> CNC ...
Hello Steffen, If you are going to allow the computer to go to sleep you need to exit Mach3 first. I have all my omputers set to never go into standby mode ...
Hi Brian, that is not the problem, I do not have any automatic powersaving modes. At first, with Mach3 running, it is not possible to enter suspend mode (msg ...
From: mach1mach2cnc@yahoogroups.com [mailto:mach1mach2cnc@yahoogroups.com] On Behalf Of stytoons ... Right this was my point as well. ... So this is a 'double...
Me too Jeff. <grin> ... From: Jeffrey T. Birt To: mach1mach2cnc@yahoogroups.com Sent: Friday, February 01, 2008 1:39 AM Subject: RE: [mach1mach2cnc] Enlarge...
... neither leg is grounded? While no insulation is perfect, there is a lot more than resistive coupling to ground. If you mount a transformer on a steel...
I can relate. I almost bought a W6 once. That was a monster of a tractor. I know of some guys around me that have 50+ tractors sitting in barns. They are...
If you are just driving one device with a power supply, then the reason for star grounding may be irrelevant. The star ground is to minimize ground loops. To...
Hi Gabriel. Yep....I'm in Arkansas. I'm gonna move this lumber if you're interested. I have it in my brothers shop building and he wants the building back! :( ...
... It is very rare that I have found a reason not to do so. Of course, there are always exceptions but I doubt that you would find one in a typical CNC...
Although this turned out to be the funniest post I have seen to date, it unfortunately does not solve the problem. Using the shift (I'm really watching my...
Kerry: If you have no home switches, then press RefAll, I suspect your machine cooridnates are so far off zero that its causing the shrunk image.. Pressing...
Greg, Since mine was set at .050, when it hit the switch and move off, I just though it was moving what I set it at. i had to try the larger number. I learned...
Beyond that they use differential step and direction signals, the same as we do for differential encoders. Just chuck a TTL to RS422 line driver at one end and...
Bill, Soft limits were set as follows: X max 10.00 min 0.00 Y max 999.00 min -999.00 Z, A, B & C all the same as Y I changed Y and Z to the same as X and that...
Hi John, Thank you for the spread-sheet for the pulley data, it makes life a little easier, saves looking through difference catalogues. How would you make a...
Kerry, The soft limits should be the size of your travel or table in each axis from the zero point. We produce cnc routers so all of my mins are 0 and maxs the...
Hi Keith While speed mode is wrong, I suppose loosely you could say that the voltage output from the pixie calls for some torque, or incorrectly speed, both ...
On a DC servo you cannot ground the motor wires, though the DC supply is often grounded where it enters the servos. There are some AC drives connected in star...
Good job I only use recycled electons for my computer and my brain was melted years ago. Have your tried charmin it is realy soft? I can only guess that...
Thanks Mark, that is just what I needed something to look for. So far so good, no oscillation and crisp rapids and stops. Keith ... voltage ... rather than ...
