... page? Mine ... Servo's electronic acronyms file omits the one commonly used for idiots like me :=( The controls were not on Program Run screen because my...
I'm having the same problem here. Every time the cycle ends count is 100. ... John, fixed the file, sorry 'bout that. Uploades as 18sq one up_r2_FIXED.zip ...
John: Yup, I probably screwed up something again. I will remove the multiple referances to the Safe_z and Inhibit variables to see if this corrects it. The...
Hi All: It still says 1.001 on the site and in the program , but it is actually 1.002. The new driver is also updated for the non-apic people. 1) Fixed G-Mode...
Art, Would it be possible to configure the G Code interpreter so that the file can be started at any line that contains the required preparatory code. During...
Servo: Already there. The "set next line" key preps the cycle/start button to start from the line you were on when you pressed it. This is different from RunAt...
Hi I just installed a 2nd parallel port card My printer recognizes it but Mach1 does not. The port address for the new card is not listed under any of the...
Frank: To remove all registry setting, you have to run RegEdit and select the key HKEY_CURRENT_USER/Software/Mach1 and delete it. Its the only way. Mach1,...
757
c7601@...
Sep 1, 2003 11:24 pm
ART ARE YOU GOING TO PUT BALL SCREW MAPING ON MACH 2 SOME DAY [Non-text portions of this message have been removed]...
I have downloaded different versions of mach2 and they all have different response. Load mac2 c-2 and I can generate g code from dfx file and get a tool path...
... <snip> ... the trouble here. Several changes were made however. ... holdover from Mach1, where the logic tab actually loaded its info from the registry to...
.... and on minimising Internet Explorer after posting the last message the minimise animation was very slow and jerky. Mach2 shows pulse rate of 100....
... Much, much better :) - Thanks Art!! No spindle slowdown, no stepper lockups, no spurious X axis moves! Still a delay initially while spin adder counts up,...
... Hi John - nothing untoward here in that department? I've got Mach2 lathe running a test file (not cutting) Email and Internet explorer running, I can jump...
John: The 100 pulse rate will occur if a multi-media call is made to Windows. If you had explorer open, its possible a small multimedia call was made (for an ...
... holder ... easier ... I've good success using a small adjustable parallel bar between the work and the tool. Get within about 3/8", adjust, measure, and...
... tell my plasma cutter to cut, is this going to be possible. Do I have bad downloads, am I downloading the wrong trial version,are there some settings to be...
Art - a few observations from some test threads: If actual spindle speed is not same as requested speed spin adder keeps going for ages before first cut...
... Windows. If ... made (for an ... Yes thanks. I would not have run Mach2 on a machine with other software and testing it in the office did not think of...
... of ... <snip> ... the ... Yep! me too. Mach2Mill manual Fig 7.10 shows technique in Mill context. Corrections screen is handy for adding in the gage ...
Hi Art, Maybe I didn't explain myself correctly. The problem is with the other axis (the one that dosen't need backlash correction). In a full circuit the axis...
Art, In view of the ever growing complexity I am wondering if a 'popup' help reminder system might be added to Mach1-2 similar to the little boxes that appear...
... Strange. When the spindle speed is commanded, it simply sets a frequency for the spindle axis and doesn't use it again. Let me explain the variables in use...
Isak: Is this in a G2,G3 move? On mine , both axis slow to a stop before correcting, then both axis accelerate. (Unless CV is used in which case it works as...
... help reminder system might be added to Mach1-2 similar to the little boxes that appear under the cursor in windows apps. <snip> Dear PJH and everyone: Art...
... No, I think you misunderstand - If commanded is say, 400 and actual is 420 it takes ages. If commanded is 400 and actual is 400 adder starts instantly and...
It is in a G2 full circuit move (G2 x0 y0 i10 j0). It seems that the CV light has no effect on the behaviour. I changed it by G61/G64 MDI command, and...
... Even this should not matter. The only numbers that are important are "Normal SPinCount" and "Current SpinCount"... ... This is a good sign, the acc and dec...
