Many times we have gone for a sail and the wind has died while we were miles from home. The only way to get back was to turn on the iron jenny. There is no...
Peter, I have a small solar panel on my West Wind 20 that I got at West Marine. It does a great job of keeping up my batteries. It has a nice mounting...
... Does this help? http://www.mad-mac.com/luger-voyager-30-ketch/mast-raising-lowering.htm Complete factory specs, instructions & diagrams for the Voyager 30...
Hi my name is Chris and I bought a Voyager. It needs a lot of work so I have a couple of questions. 1 Were the deck meets the hull, under the rub rail the...
Hi and welcome aboard. 3M 5200 is all but permanent. Once in place if you try to take things apart later it will take fiberglass or gelcoat with it. If the...
Be careful if you use polyurethane sealers or glue. That stuff is super strong. If you do need to fill a large void it is an inexpensive alternative to using a...
Ernie's registration information included the following comments: "I am getting a Luger Fairwinds 27 - trying to learn more about them." Welcome aboard!...
Hi and welcome aboard. Another biggun. There are no dumb questions. mike of About Time ... _________________________________________________________________ ...
thank you very much.i will be picking her up monday.needs a little tlc .has small crack by keal that needs to be fixed.does anyone have any inside picks of...
Ernie: The best source of interior and other information about your new boat is a new original Luger catalogue. Joanie, moderator of the Luger Mooring site has...
That's a very good question - and I can't answer it right now. Today (July 9th) my internet provider, Atlantic Broadband, literally "pulled the plug" on all...
I don't believe they did that without warning! No need for you to apologize, we need an apology from Altantic BB! Do you have the files? We can recreate on my...
Peter: Thank you for your kind offer. Fortunately, I always keep a back-up of my files. Also, I discovered there's a place on the web that has "archived"...
The Luger Sailboat Mooring's index page is back online. Our homeport has a new location on the internet, but if you type www.lugerboats.com, you will ALWAYS be...
Anybody ever beef-up there chain plates on there voyager. They just don't seem very big and there only into the deck. I'm repainting the hull and deck so now...
I'm rebuilding my voyager to sail on the great lakes for now but some day it will be in salt water so my question is can I use stainless steel fasteners and...
Stainless should be fine but I think you can use plastic thru hulls and never have to be concerned with corrosion. A lot og depth sounders and speedos use...
Stan's registration information included the following comments: "I live in Missouri, on 65,000 acre Bull Shoals Lake. Found a '79 Voyager that was swamped,...
"..It seems that if I install the foam under the cockpit bridge it should be enough for an emergency float..." Foam is useless as emergency flotation if you...
On the '73 Windward I built there was foam under the cockpit floor, under both quarter berths and under the vee berth. In all cases the areas mentioned were as...
Just wanted to introduce myself and explain why I found this group. My name is Stan Warner and I live on beautiful Bull Shoals Lake that straddles the border...
Hi my name is Chris Ellis, I too have just bought a Luger Voyager. I live in north west Wisconsin but I picked up my boat at Black Jack marina on Mark twain...
As far as you engine goes pull the drain plug and drain the oil. Water settles to the bottom when it sits. If you get water out of it then you have trouble....
Spent two days on the water with no issues. The Windward tracks like a dream with the keel up. I went with a 40 lb thrust trolling motor, it was more than...
Hi Stan: My Luger 26/27 was purchased originally in 1976 but never got finished. When I dragged it home I hoped the hull reinforcements were OK and would not...
Mike and Chris, Thanks for the ideas and info. I went to pull the motor yesterday and the wood it was mounted on crumbled. Took some of the wind out of my...
I would not do that because you can't reinstall the bulk heads with out the deck being on and most everything else runs off the bulk heads. I don't think...
By the way if you need any dimensions for the inside of your boat let me know right away and I'll try to get the before I get to far with the tear down. The...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
