CONTENTS ... * LIST ARCHIVE & SEARCH * MESSAGE DELIVERY OPTIONS * VIA THE WEB * POSTING TO THIS GROUP * CHANGING YOUR SUBSCRIPTION STATUS * RELATED GROUPS *...
8712
lrk-torquemax@yahoogr...
Jun 1, 2005 9:35 am
Goedendag ;-) If you find you are getting too many messages, you can also read them on the homepage at http://www.yahoogroups.com/group/lrk-torquemax/ In order...
Building my own edm was ended with fiasco. Someone did advice to go to local edm shop. OK, I did. The chief of the shop told me that it is not passible to gut...
I have a good bit of experiance with wire edm machining and i can tell you that any non conductive material that is in the cutting path will cause the wire to...
Even thin film of lacquer, will meet the wire edgewise? Ohh .... :-( Then how to cut the slots (see the picture in my album /torr18_20.b. jpg/) Herbert ... ...
Then how to determine the distances between the slots, after every turn (every 18 slots) it need to be a little bid bigger (or smaller). May be better to wind...
Yeah, To mill between the two thicker palates when you are making the "normal stator". When axial flux stator - then I need thick outer steel ring and inner...
The company I work for just aquired Extreme Energy, makers of the 'Chile Pepper' BLDC motor http://www.brushless-motor.com/ I would like some feedback...
... I don't know for sure, I think the ammo is an automated winding while the Chili is hand wound? I did find this however; Not wanting to let it go at that, I...
Hi, I was just wondering if anybody has been making motors out of used hard drive bits. I've got a few toasted hardrives around and I thought I might try and...
Hi Herbert, I just looked at your stator in the album. That is a tough one to make. I agree that wire EDM won't work due to the insulation and glue. Powder ...
Thanks Mike, I can make molds, as well as casting under pressure (or vacuum), it is not a problem, I have casted much more complicated pieces. The only problem...
Sorry for stupid question but I have no idea how to run brushless motor. Do I need controller for brushless motor or is it some other way to run it like...
No it's not a stupid question, just the first one people ask ;o)
Yes you need a brushless controller, they are getting cheaper all the time,
perhaps down to...
Hi Herbert Maybe it's a good idea to go to a shop who has a rapid prototyping machine (3d printer). In the early days of rapid prototyping only plastics good...
Goedendag Dave, Usually it's only the stator you can use. The rest depends, most of it is pretty heavy and needs a bit of shaving/holing. Search for 'hdd' or...
Thanks Willy,
Oh yeah, its nice and I know it as well as where they have Rapid Prototyping machine. Im tired to go
from one company to another - they are not...
There's gotta be a way to make one! So, is there a way to make a simple, sensored brushless motor? I remember R/Cmicroflight.com made a brushless motor for a...
you sure that isn't 4µ7 or something instead? Would be about right for the size.. If you have a photo i can tell you for sure... ST On Tue, 31 May 2005...
you sure that isn't 4µ7 or something instead? Would be about right for the size.. If you have a photo i can tell you for sure... ST On Tue, 31 May 2005...
you sure that isn't 4µ7 or something instead? Would be about right for the size.. If you have a photo i can tell you for sure... ST On Tue, 31 May 2005...
On Tue, 31 May 2005 20:42:52 +0200, Stefan Trethan <stefan_trethan@...> ... Not sure why this old post is appearing now. Had problems with posting from my...
you sure that isn't 4µ7 or something instead? Would be about right for the size.. If you have a photo i can tell you for sure... ST On Tue, 31 May 2005...
... I don't think it would be any use as a sailplane winch. The F3B winches pull 300-500A to get their 5 hp. A brushless ESC and motor that can handle that...
