I just built my first cd-rom motor. It is a 9 pole motor and I wound it with 16 turns of the 26g wire. I am using a jeti 40 amp controller to test with, and...
Hallo to everyone, after my holiday I try to understand my trouble in winding. In my LRK (see photo in Photos area)the caves aren't completly full, because if...
799
Wim Hanssens
willem.hanssens@...
Sep 3, 2002 4:48 pm
... No it is not, I calculated 1.05mm dia wire with the "tool", Klaus managed to get 1.1mm wire in(just), so for an inexperiënced "winder" it is correct. ... ...
Hi Steve, Check your windings, are they ok? No shorts between stator and a winding, no shorts between two windings? A winding diagram, for demonstration...
No, the coils are not shorted to anything, I think I have reada few places that weak magnets can cause this to happen? it is a one piece magnet and it isnt...
Hi all Now the motor story continues. Yesterday I received the magnets for the slowflyer motor LRK-290-5 20W 2x0,5. I put a new picture into the photo album,...
Hello all! Does anyone know if there ar statorsheets available vith 34.5 mm diameter, I saw somewhere it mentioned but I don´t remember where. I did send a...
Hello, I have wound at least 5 cd-rom motors from 15 to 18 turns and none of them operate properly on a Gold label jeti 6amp controller. I don't think the...
If you can get your hands on one of the Jeti/Hacker/Masterseries, or an ESC that has adjustable timing, it would be interesting to try different timing...
... Hi Tom, http://www.batt-mann.de/ seems to have stator packets of 34.5mm outer dia, 6 or 11mm inner dia, in different lengths. ... I have had same problems...
Hi Jani en Tom, @Jani I was under the impression that www.batt-mann.de does not deliver outside Germany. Am I wrong to think so (I hope I'm wrong)? If you...
Hi Steve, ... places that weak magnets can cause this to happen? it is a one piece magnet and it isnt very strong. Weak (ferrite or the grey plastic bonded...
Hi Dieter, How do you manage to glue the magnets in pairs of three? See: http://us.f1.yahoofs.com/groups/g_3205347/Dieter+Doerr/ ...
810
lrk-torquemax@yahoogr...
Sep 5, 2002 4:11 pm
This lrk-torquemax mailing-list help message is sent-out every month and upon subscription. CONTENTS ... * LIST ARCHIVE / SEARCH * MESSAGE DELIVERY OPTIONS *...
Hi Ron Your question: "How do you manage to glue the magnets in pairs of three?" The answer is very easy, If you have the right tools available! I made it with...
Hi all, I was just looking through the building instructions of the Torcman 350eco (tm) and started to wonder how the windings should be connected if one...
Hi all Yesterday I finished the development form my LRK-290-5 motor. In summary: I can replace my SPEED 400 (gear 3,33:1) at 8 cells in a slowflyer with the...
Hi Christian Thanks, that you like the little motor. To make the motor with 10 mm magnets, I think you will get the following additional weight. For 5 mm more...
Hi Dieter, Thanks for the information. Looks like a LRK 290-10 could be a speed 480 killer. Regards /Christian ... From: "ddoerrheli" <ddoerr.heli@...> To:...
Hi all I have some more information about my LRK-290-5 motor. In the meantime I received one of those very popular Hacker Jeti (Master 18-3p) controller. With...
Can someone please give me the URL to the very accurate motor test stand that I think one of the LRK founders/promoters made? Thanks in advance, Neil Stainton ...
Hi Neil, You'll find it on Peter Rother's page: http://www.aerodesign.de/peter/2001/LRK350/index_eng.html Menu item "Performance Measurements on Electric...
The German magazine Elektro Modell issue 3/2002 have a VERY FINE construction article about building a PC motor tester...mine vill be ready soon. Look at :...
Hi all, If you're interested in subscribing to the German "Elektro Model"l magazine: http://www.neckar-verlag.de/modellbau/elektromodell.htm Is there a French...
822
Jean Luc Boutillon
jl.boutillon@...
Sep 8, 2002 1:00 pm
No Ron , no magazine specialised in Electrified models exist in France. We have 5 magazines (Fly, Modèle Magazine, MRA, RCM, Looping) which all treat from...
http://babelfish.altavista.com/ Hi Fellows, this is my first post I have been lingering in the background for sometime now. The reason for my post is to post...
Don, Thanks for the link... It will come in very handy as I find myself finging many sites with interesting pictures & articles and not being able to...
Hi all, Another web site translator: http://www.google.com/language_tools?hl=en Dictionaries: http://dictionaries.travlang.com/ Now, finally, you can figure...
Hi Jussi Many thanks for the info More precisely: Have we to calculate successively (A+B+C)/3 - C ; then (A+B+C)/3 - A; then (A+B+C)/3 - B ..? to process every...
