Hi there, just received my LRK kit from flyware. They have coated the stator sheets with a heat-activated adhering lacquer. This means that glueing the sheets...
187
Steve Garlick
sgarlick@...
Dec 1, 2001 10:26 pm
HI all, My apologies, I seem to have picked up a virus, that automatically mailed itsefl to you. The following fixes worked for me. ...
... Yes. See: http://www.rconline.net/k-forum/Forum37/HTML/000209.html http://www.rconline.net/k-forum/Forum37/HTML/000207.html Met vriendelijke groet, Ron van...
Hi all, @all The Badtrans virus cannot be transmitted via the lrk-torquemax mailing-list becayse the list does not allow attachments. Over the past two weeks I...
192
peter_rother@...
Dec 7, 2001 12:34 pm
Hello, I have new reading for you for the weekend: "EM 4/2001 Performance Measurements on Electric Motors " All the Best Peter Comments welcome!!! ...
193
Marcus Wright
wrightmw@...
Dec 7, 2001 2:24 pm
Anybody interested in a group order from www.flyware.de I am making a list of people in the US that want to order. This would help with the shipping cost of...
Hi, What difference will it be with different thickness of the magnets, 1,8 2,0 2,5 or 3 mm? And the iron ring shoud the material thickness change with magnet...
Marcus, I'm interested in ordering from from www.flyware.de. Thanks for putting together a group order. Eric Ashby ericashby@......
196
Marcus Wright
wrightmw@...
Dec 9, 2001 9:18 pm
You are more than welcome. I will collect names for about another week or so then contact everyone for their order. Marcus ... -- ... Dr. Marcus Wright NMR...
... I really appreciate Max Zuijdendorp going to the trouble of translating this article so excellently. I have a subscription to ElectroModell, but my ...
... 2,0 2,5 or 3 mm? For a given permanent magnetic field, it's better to have thin magnets. That way the magnetic resistance Rm (has nothing to do with...
Hi Ron and Christian, I do not agree with Ron. It is true that for a thinner manget the magnetic resistance is lower, however this is canceled by the fact that...
Hi there, my flyware LRK 15mm motor did his first revs. yesterday and I just wanted to share the feeling of success that only DIY parts can give you... Regards...
Hi Merijn, ... This would have been a better way to say it: If you have two magnets, same strength ("for a given permanent field"), same length and width,...
... It will drive a Graupner Zoff (speed model, wing span 120cm, weight 1100g). Goto www.geocities.com/fsv_bottwartal and click on 'Modelle' for picture(s) and...
204
peter_rother@...
Dec 11, 2001 2:29 pm
Hi Merijn ... I would be very interested in. But it must not be the interest of everybody, so you can send me it per email. I have some calculation on my own,...
Hi All, It will take a bit of time as I will have to set up a proper calculation. I will try to make some time for it this weekend. I am not very familiar with...
Hi. Today I tried my LRK 15 with a prop (11x6 Graupner). It draws 25-27 Amps @ 8 cells, has a thrust of about 1000g (model will weight 1100g!!!) and gets no...
207
Kenneth & Mary Holden
ken.mary@...
Dec 12, 2001 12:05 am
Hi Peter: I think that a lot of us are interested. Please put the info to the list. Thanx and bye, Ken...
Hi Ron, Merijn and all other I made a test: magnet thickness 3mm and an iron ring 1,5mm thick. The performance was within 1% of my earlier setup. The original...
Hi, I have built a micro "LRK200" (8-pol) on a stator from an old IBM 20Mb hard disk. Weight 35 gr. Put 50W with 82% eta and 7 cells. Turns a Graupner 4,7x4,7...
Say Group, I am a native Texan and resides in Houston, Texas, USA. I am a retired engineer/manager from the petroleum industry. That should give you some ...
I would like to use a LRK in a Robbe Impression glider. We're going to build a few as a club project. For those who don't know the plane: it has a span of 206...
G'day Stefan, I have an AXI LRK type motor. In a Great Planes SPECTRA glider that came with a 550 motor. Originally about 1450 grams, good climb, but too high...
