Hello That outrunner is the "Gigatex" made by Lubos Chvatal (Freeair) Louis ... De : Ron van Sommeren <ronvans@...> À : lrk-torquemax@yahoogroups.com;...
Eeeh, make that 21statorpoles, not 18. Thank you Martin Götzenberg :) Vriendelijke groeten ;-) Ron van Sommeren near Nijmegen, the Netherlands ... From: Ron...
Goedendag ;-) A new kid on the block: www.rcadvisor.com Prettig weekend ;-) Ron van Sommeren near Nijmegen, the Netherlands -- I am using the free version of...
Goedendag ;-) [Quote Ralph] "... at the beginning of climbing I found 153A = about 3000watts.after 10 sec and under full throttle only 1900 watts are needed...
Life has a habit of getting in the way but I've managed to put a little more energy into this project. Look at http://www.warmlandet.com/ to see the start...
... dare ... Unsprung weight becomes a factor when the ratio of unsprung to sprung weight gets too large. So the heavier your car is, the heavier you can make...
Thanks for the feedback Ryan. This unit is indeed going to be heavy. Saving weight will need to be a consideration down the road for sure. Right now we'd be...
... I am not familiar with that, though the kelly 72V (actually 100V max) 300A controller might be a good controller to start with, its around USD$600 ...
Goedendag ;-) 'We' need some help with this Halbach magnet array inrunner please: <http://www.rcgroups.com/forums/showthread.php?t=867564> Vriendelijke groeten...
Hi Guys! Well I'm working since quite a long time on a brushless outrunner generator project. I've succeed to solve a lot of "issues" concerning this project...
If you are testing without a load, all the energy generated is dissipated as heat and burn the coils. Attached to a large resistor (or discharged battery), the...
Hi Rick Not exactly. Without a load, the losses are only iron losses (copper losses are zero) The corresponding heat is generated inside the laminations (eddy...
Hi Hadrien IMHO If you desire 60W under 12V you need 5A But 5A and internal resistance 4.2 ohm means 21 V .. That is not compatible. Your windings are too much...
... Something seems wrong. I calculate you'd need 3 parallel wires each 40m long to get 4 ohms resistance. As others have pointed out, you need to lower the...
Hi all! First thanks a lot for your time :-) When I've said "under load" I meant that the generator was connected to a batterie and charging... :-) sorry for...
Hi, Well... I've never thought about it.. Won't have any problem to linearize it? As soon as my target is DC... well I do not know... best regards, hadrien ......
Hi, well my generator is about 50mm ext diameter... for 60mm long... But I still don't really understand how it's working... How look the output? is it DC?...
Dear Hadrien, I have build a generator with permanent magnets and I did the following things to make it work. To determine the number of windings I made a...
I haven't tried this but to me it seems that you could make a better generator by having strong magnets and a field weakener to cut down the cogging at very...
Hi Hadrien There are several ways to minimize cogging in an outrunner alternator (generator), without affecting the output/efficiency too much. Rounding the...
Dear Hadrien, I have build a generator with permanent magnets and I did the following things to make it work. To determine the number of windings I made a...
Goedendag ;-) See http://www.wattflyer.com/forums/showthread.php?t=35216 Vriendelijke groeten ;-) Ron van Sommeren near Nijmegen, the Netherlands -- I am using...
Hi all! I'm back... I've founded some new information and I think it would be good to share them with you. There is a table called AWG (american Wire Gauge)...
I came across this website today, and was shocked to see the following formula: Efficiency = Power Out / (Power In x SCEF) where SCEF = Speed Ctrl Efficiency...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
