For those doing the run of the latest Softrock transmitter, I've put together a test tool to exercise the TX side. As well as the mandatory tone generation...
Hello Duncan Using the IQgenerator (works with windows drivers and asio4all as advertized...) easy to balance an cancell the other sideband. Now just add the...
... Thanks for the feedback and good to see that you ran a cancellation experiment. It's looking more likely that the 'cal' for transmission is going to be...
Version 1.1 is the type number for the Transceiver version of KGKSDR. There is no TX on there yet, however... the audio side of the receiver has been...
Apologies to anyone who has recently tried to get the new 1.1 file. The link on the download page was pointing to the _old_ file, i.e. the receiver. This has...
Hi Duncan By using version 1.1 I lost the ability to run 2 instances of the program (still works with 1.033) Its the same with other programs once you go to...
... Hmmm... that is a point that I hadn't thought of, thanks for letting us know. V2.0 will have dual receive but for now it should be possible to run the old...
Hello Duncan, What a surprise to get already a glimpse of the new kitchen! All went well. It did recognize my soundcards (AC97 & SB) via ASIO immediately. A...
... Hi Guido, yes you have noticed that the latency (propagation) is down really low. The nice thing is that it will get down even more for fast CW QSK...
Hello Duncan, Trying out kgksdr 1.1 and getting the following message. Access Violation at Address 00403917 in module kgksdr11.exe Write of address 01903830. ...
I cannot get the calibration to work. Old V 33 works ok with good nulls. I am not sure which of the Speaker Out options to use. Only #7 and #5 produce sound....
After about 5 to 10 minutes the program jumps to 100% cpu as shown in the Task Manager. The program's CPU freezes at 57%. It continues to provide receive audio...
... Hi Dick, I think I know the answer to this one too. ASIO4all is replicating the sample slip problem in the soundard, and the new KGKSDR does not have the...
... Hi Dick, this freeze has only just started happening to me also. It does it when the calibration charts window is open and I think I know why... When...
I had it happen 3 times but I do not recall the conditions in any case. I was more interested in a way to get out gracefully which ended up in the Task...
Try closing the new program and then starting V1.1. In my system I end up with 33 starting AND 1.1 starting. Now have both running. Something you may not...
Duncan, I consider it as a privilege to contribute a tiny bit to the birth of this remarkable application, hence my few remarks that are probably nothing more...
... Hi Jean, the depth cannot be chosen. The ASIO host code that I use from Toby Bear and Christian Budde in Germany presents the samples as either a single...
... It's worse than that :-( It looks like ASIO4all is fixing the sample slip, and KGKSDR is also "fixing" it so you end up just as bad as where you started....
Ok, looks good now. Calibration works well in manual mode. Signals will be stronger in the morning so I can evaluate the automatic calibration. CPU with new...
This condition continues to occur. It seems that you have to have the calibration screen up AND the automatic calibration checked. I also have my calibration...
The "D:" in my example is the drive/disk where Windows is located. System name refers to the name you assigned to your computer when you first loaded Windows....
... Thanks for your help Dick. I think I must have an odd installation of XP here. I cannont find Application Data in Docs & Settings. As must be obvious I am...
... Hi Dick, thanks for the info. I will try to duplicate that here and leave it running to see where it goes pear shaped. There was a message last night from...
... Hi Dick, I take it this is for the manual calibration? There's a guess button which does all the work for you, I don't think I've had much cause to press...
... Sorry Jean, I forgot to answer the question about sample speed. The way I understand it works is that the driver (1 driver for your two soundcards) swaps...
... Hi George, If you right-click on the start button and 'explore' you can drill down to the KGKSDR folder. I've put a screen dump in the files area of this ...
