I did some further studies: I can easily achieve TX image rejection of -60dBc to -70dBc in the manual TX manual cal procedure. I've calibrated the whole 96kHz...
Once again more studies and testing done. ... Even tried this and it didn't have any effect. I can slide the frequency slider and have at least -60dBc image...
... Hi Janne, I will have a bit of time tomorrow to look at this. If you don't hear anything on the group here by about 1800 UK time, please send me a...
This needs kgksdr and loop.dll set up and running. It does only work in RX yet ... if there is intrest i might do the TX as well. Instructions here: ...
Cesco,   Is there interest? Well heck, sure there is! I've used MMSSTV with my traditional radios and been really happy with it. If there is even a chance...
Hello, have a problem with transmitting CW. My notebook has no RS232 interface, so I use a RS232 PCMCIA card from EXSYS type EX-1350. After installation it has...
Hello, now I checked the signal CTS and DSR with the Serial Port Monitor 4.0 by Eltima Software. CTS and DSR are changing so my hardware seems all ok, but...
... Hi Uli, can you get a meter and measure the voltages on the RTS and CTS pins while you are keying? As an aside, COM1 - COM4 are reserved for internal...
Hello Duncan, thanks for your help. First I installed all new - Windows XP SP2 and all drivers. The RS232-PCMCIA is now COM4 and IRQ7. Now I soldered resistors...
Hello Duncan, with the paddle keyer test rig V0.3 it WORKS (but the tone is terrible) Have I missed something in the configuration of kgksdr V1.1 Tnx 73 Uli ...
... The config looks different to the wiring you are using, that may be the problem. You can ignore the dit for now as paddle is not implemented on KGKSDR...
Hello Duncan, yes I have forgotten to mention that I have changed my configuration. In the Photo area -> DF5SF you see my settings. CTS and DSR work with the...
hello, I like to work also in digital modes (PSK31, Olivia ...). Is there a possibility to connect mixw2 to kgksdr in receive and transmit mode. If yes, please...
Hello, in Calibration Options only Manual is checked. Now in Options -> Set RX manual cal point... I calibrate every 2 kc and get a SIR of better than 80dB. I...
Hi, I have the possibility to upgrade my motherboard. Now what is the best choice for KGKSDR transceiver - Intel Core2Duo 2x3GHz - Intel Core2Quad 4x2.5GHz ...
... Hi Uli, It's a close call, KGKSDR runs a single thread for the most part so my initial choice would be 2x3, but there is always other stuff running on the...
... Hi Uli, Can you check the Options | Transceiver | General screen and look at calibration options. Ensure that you have the following settings: Manual:...
... Hi Janne ... well I have the same problem, but it is not so severe. With manual calibration I get the image about -65dB down. In TUNE the image is always...
... Hi Uli, thanks for posting the screen dump. The left side of the picture looks very wrong, the phase keeps going up and down and the numbers are very low....
... Hi Duncan, I added the screen dump of the amplitude correction. The TX is a Softrock TRX V6.2 (40/30m) without the PA, only with driver. The receiver (40m)...
I finally got my sound-cards setup in the program but now the software indicates the receiver is in "Standby". I do not find a "Start" button any where? How do...
... Hi, is this the receiver software rather than the TX/RX? If so, there is a button marked "Start" on the left hand side of the screen. You can get it to...
Dani, I hope someone comes in with an answer. I'm looking for this same info. I just downloaded the loop.dll and MultiPSK and it works together, but not sure...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
