Thanks to Michael Irwin I now have the answer; The trigger task CV (CVs 33 to 40) must be set to 10 hex (16 decimal) so that it will resond to both directions...
Thanks Paul I will look forward to that. Do I just put the file in the decoder directory? [I'm still a bit new to this]. Many thanks Brian Lunn ... From: Paul...
Hi Brian (and list), For the benefit of all involved (and so I don't have to send this out to more than one person) I've uploaded the decoder definition I have...
Bill, Using a MERG decoder, a CV with the value 255 takes approx 15s to read in paged mode, so I don't see the problem that you are seeing. Could you time the...
There seems to be a problem if the throttle window is closed using the X button in the top right corner before turning off track power. There's a log...
Hi I have just upgraded my decoder list with the Lenz LE1000 as per Paul Bender's instructions and rebuilt the decoder list. Unfortunately DecoderPro now...
Brian, I don't believe addition of the decoder definition file is the cause of the problem. I'd suggest a system (PC and Booster) reboot. If that doesn't solve...
Bill, Do you have any different decoders that you can try reading in paged mode? I just looked through the SPROG code and remembered that paged mode reads...
I recently bought a Loco Buffer-II. I am using the Digitrax DB150, so I don't have read-back (that's OK for now). I created a roster, plugging in the CVs I...
Jim, The beep you describe is a function of the DB150 Command Station, which can be enabled/disabled through OPS SW 49. Setting this OPS Sw to closed should...
... Sw ... Thanks for the reply Bob. I spoke to a buddy about this, and he said about the same thing, absent disabling it. Basically, he said it's the DB150...
I'd like to change some of how the JMRI SignalHead objects work. As a reminder, SignalHead is supposed to represent a single SignalHead (duh!): Something that...
Hi All, I recently replaced two DH121 with a pair of DH123 to get the benefits of better motor control. Things acted strange during programming. I usually use...
HI Bob, ... Actually, the logic you have above is wrong. It sig22 should show a stop indication (RED) if block22 is occupied. As written, it will show a ...
... [..] ... yes, with a otherwise fine TCS T1. what happened was that I programmed 0 as it's short address, and even though I intended to use a long address...
I'm using a Fleischmann Twin Centre connected to my PC through the standard RS232 serial cable; however I can't seem to get Decoder Pro to work with it. I have...
... I respectfully disagree with your statement/logic. "Approach Lit" signals DO light when there is a train on the segment of track where they would be...
... There are two things that can stop a Twincentre from working with Decoderpro 1. I know the original software does not support using the serial port as a ...
Alex, The Twin-Centre doesn't support the LocoNet through the standard serial port. It needs to be updated, but this update is not available yet. The only way...
... I have made the changes to JMRI to handle the hardware handshake, it should be available in the next release. I guess I could email a new jmri.jar to ...
Thanks for the message, I have updated the Twin Centre to version 1.1 of the software and enabled Loco Net, however it is the settings themselves that I am ...
... Decoderpro ... port as a ... needs to ... small for a ... Decoderpro, ... through the ... which is ... software ... I updated the Twin Centre with the new...
... I do like the idea that a signal can be 'unlit' to allow approach lighting, but that the signalhead object can still correctly report the aspect that the...
... OK, the answer to this is probably better researched on the IBX (Intellibox Exchange), another Yahoo groups list at IBX-subscribe@yahoogroups.com which is...
... Oops. I added "else" parts at the last second as I was sending the email in an attempt to make it more readable but they made the logic incorrect....
... I don't see how we disagree. We seem to agree that they are only lit when they would be visible, and that the logic is independent of the fact that they...
Bob, I have a question about signaling logic on the panel I am building for the clinic in September. Since it represents a section of single track mainline, I ...
Hi To set the Intellibox/Twin-Center in loconet mode by default change the following special options. SO 2 in value 4 SO 5 in value 5 SO 6 in value 255 And set...
