... Hi Mark I am sure someone with more experience will step in here, but if I were you I would build a "technology demonstrator" in simulator mode. I would...
... Yes, Uhlenbrock update the firmware in their throttles across the Loconet, and I imagine other devices in their product range that could be updated as...
hi all, has anybody used jmri to connect to the new uhlenbrock intellibox 2, i can connect using locobuffer-usb but i have tried with the built-in usb...
Kip, Glad it worked for you and thank you for the feedback. I wasn't 100% sure if it would work as I don't have access to a WiThrottle device so couldn't test...
Hi Folks: Yes, the Digitrax DT402x throttles, the UR92 transceivers, the LNRP and the PR3 can be firmware updated, all using the DigiIPL software. Regards, ...
I'd rather see us consider an option in the preferences that will enable/disable that action. Two reasons: 1. Messing with the command station can have...
Mark, You could also consider leaving it as a computer panel solution if you used simple notebook computers as the remote panels. So a simple wireless router...
Hi I have been asked to do a short magazine article on JMRI. (On what JMRI can do, not how to do it). It seems to me I that with the best will in the world in...
The key is attribution to the original source. By clearly including that sort of connection to the source (like jmri.org) pretty much covers what you take for...
Thank you Peter...very helpful. I think I have the hw side in hand but it is the Panelpro/JMRI side where I am very much a novice and your suggestions will...
... I'll get to poking at code as soon as sourceforge is fixed. :) ... I could not find that from Google, but it's what I needed to know. Note if you go to...
thx Ken...though I am not sure I follow very well. I will be using a laptop in the dispatcher room adjacent to the layout room. I would like the Dispatcher to...
Also note that I will be driving 6 TO semaphore signals as well as the fascia LEDs at a not too distant point so I need to have a solution for each TO station...
Peter: To play the devils advocate would be to ask if the policy of Yahoo! is that what has been posted becomes their property... If not I would look at a...
Thanks Jim and Ken I should have mentioned that this small article (page and a half) is intended for the NMRA BRs in house Magazine, "Roundhouse", and also...
Mark, If you were looking for other examples, your use is similar to the 'Maintainer Call' lamp feature of many CTC panels. The other thing to keep in mind is...
Ken, I have had to do a similar thing with the Ecos, where it is possible to turn off the auto-population of the sensors, turnouts and locos into JMRI. It sits...
Can someone explain to me the difference in these two boards and how many signals each can control. Thanks Jay Beckham Modeling the Chicago, South Shore, and...
Yahoo TOS state that all content is copyright of the contributor. Yahoo claims no copyright on any material submitted by users. Sometimes there are very few...
Thanks for the information. So it is the RSSD that I need because I am using 3 lead LEDs Jay Beckham Modeling the Chicago, South Shore, and South Bend...
Ken, I agree that this is a change to JMRI and not something the hardware vendors should do. There may be under-the-hood changes in the way JMRI initializes...
HI Chuck, ... But let me ask you this question. Do you really have control over when devices are initialized? I will argue that you don't. The reason here is...
This detector incorporates two infrared sensors, they'll detect trains at two locations on the layout. The detector reports the sensor states (trains present...
Paul, I may be flying under false colors on this issue. I do not (as yet) use JMRI to control my CMRI hardware. My custom software, written in an older, more...
... Excellent! ... I don't think writing your own words is a problem in this area, even if they're very similar to the words of somebody else. Sometimes...
Curious - in my system, the DigiIPL "find devices" operation does not find an LNRP. Perhaps the "Test" button comes into play for firmware upgrade on the...
I use 4 DS64s to control my points. I use a panel or the DCS50 to switch the points but when I use JMRI (2.11.1) there seems to be a delay. I also cannot read...
