The JMRI users discussion group is for people using the JMRI model railroad suite of software. JMRI provides several useful tools: DecoderPro - makes it easier...
23675
jmriusers@yahoogroups...
May 1, 2007 10:27 am
====================== HOW to ask your question ====================== One of the most common questions about JMRI is "How do I get it to work?" This isn't...
Claude, For $10 NCE will replace any decoder with any decoder in their lineup. It is a good chance to upgrade to the latest model or to get a decoder that may ...
The Pricom DCC tester has a couple of serial dcc packet dump modes that are not ascii. Section 5.7 in the manunal. I would like to be able to filter other type...
Claude, Here's a couple more things you can try: 1. Try "Direct Mode" programming rather than "Page Mode." 2. IIRC, older NCE decoders do not like to read...
I had no problems reading the decoder with my IntelliBox. On the other hand, the EasyDSCC system could not read a thing. I think it depends on what method the...
The big question is: What DCC system is your Decoder Pro connected to? The only system I have used with the FL4 is the NCE Power Cab and it read back fine with...
I've been running JMRI on Vista (Business Vers) for quite a few months (including Beta versions of Vista), and have had no problems at all. -Rick Beaber ... ...
Thanks for the response(s). I was able to get DecoderPro to read the TCS FL4 Decoder by increasing the resistor value across the blue/green wire to 330ohms...
Hi, Over in the Atlas RR forum we have been discussing these two decoders. See this thread: http://forum.atlasrr.com/forum/topic.asp?TOPIC_ID=36982 ...
Hi All: This is my first time with Decoder Pro and NCE (have 2006 EPROM). I can run and control a loco with throttles Tool, but I canīt program a decoder. ...
I am resurrecting this thread to see if anyone can help. I HATE updates!! I have 52 TCS equipped locomotives that I can't use Decoder Pro to program them. Here...
I was very impressed with the tutorial showing how easy it is to set up a panel and control it using a computer. My question is: What would be required to...
Richard: I have done something like that with scripts. First you have to know what block the train is in and which direction its moving. Then whats the next...
Richard, From your question, I suspect you mean hardware, not programming. If that is true, I would suggest rr-cirkits.com and the BOD8. It is Loconet...
Hi Claudio, You shouldn't need to do anything with the ProCab, as DecoderPro will switch the NCE command station to the program track automatically, when a...
Graeme: Thanks for your help, this weekend I try your Tips and check my EPROM version. I am in the way to upgrade the EPROM. Next week tell you everithing is...
The four Atlas 342 I have read back 46 for CV7. The ten Atlas 340/341 I have read back 45 for CV7. Michael Mosher http://home.comcast.net/~mjmx Member SFRH&MS ...
I have bought several Bachmann 36-553 3 function decoders but DecoderPro is unable to identify these correctly. Did anyone answer Martyn's query from last...
In a message dated 5/2/2007 6:14:50 P.M. Eastern Daylight Time, jeeper785@... writes: I am resurrecting this thread to see if anyone can help. I HATE ...
Hi, I just installed the new version of the EPROM chip from NCE and now my Decoder Pro will not read or write to the NCE system but it did before I installed...
Yeah, being a patent troll just became a lot harder. Amazon's "one-click" patent should be doomed. "Hey, let's put user-identifying data in a browser cookie!...
Has any one been able to get Decoder Pro working under MS Vista ? When I attempt to program a decoder with Decoder Pro under MS Vista I keep getting time out...
When I try to add a "delay time" to a route shouldn't it delay the Turnouts changing for that period of time? It doesn't seem to work. I am using a turnout to...
Ian, The MS100 needs to work at 16.6Kb, not 19.2. However JMRI should be setting the serial port to that speed, so what the "settings" say doesn't matter. Some...
If using USB to Serial adapter you may need to update driver to vista version for the adpater. I am still using XP but I have run the Vista compatability test...
Walt, When Turnouts are set by Routes, they normally are set, one at a time, with a 250 millisecond delay between Turnouts. The "delay time" in a route is to...
Bob, Thank you for your reply. I may well get a USB-Loconet II Buffer, but in the meantime I dug a little deeper into using the MS100 with Decoder Pro under...
