A conflict between Palm's Hotsync Manager (Com 1) and DecoderPro is the likely culprit. Com1 and Com3 share the same IRQ, thus if you've DecoderPro is launched...
Peter, When you are programming an engine, either from the programming track or mainline, you will see the 'File' pulldown menu at the top. Print is in that...
I want to know if others have had this problem. I am new to this group so I have not seen past discussions. I have a Hallmark 2-8-2 with a DN 142 previously...
... back of the CV's. After this all CV's became "02", all the previous settings were lost.< ... and found that all the original setting had been restored< If...
Here is a little background on the dispatcher program that I wrote. It has a "modern" feel to it, inspired by the screens used by the UP/ex-SP/ex-DRGW in the...
Rodney, Just downloaded your dispatcher program. Reading through your ... You need to type ctcsim.bat, not run.bat. At least I tried run.bat and got an...
Hi Don, ... From that description I doubt that the values have ever been changed from their original value. It is just that you read 02 if the decoder is ...
I think Bob Blackwell's suggestion is definitely the first thing to try if you have some other program listening to Comm1. Also, just to check, you might want...
... And thanks for the feedback. The format could definitely use some tweaking to save space, be more readable, etc. But it's a start. Bob -- ... Bob Jacobsen...
Reinhard, see my comments below: Don Borden Doylestown, Pa. dborden@... ... From: Reinhard Mueller To: jmriusers@yahoogroups.com Sent: Sunday, March 02,...
... Right now, it only works on a separate serial port from the DCC connection. It would be straight-forward to add it to the serial leads of an LocoNet MS100,...
... connection. ... Ok, Where do I configure which port this is? I can still only see the normal port in preferences. Is there another port configuration...
Bob: Thank you for the suggestion. I did not know about the sharing between Com1 and Com3. In any event, following you suggestion, I got the program to work...
Morning, I have been working on a Digitrax DCC system for three years. While I really like the flexibility of DCC, every time I put a loco on the track and ...
... Can you read or write a CV from the Digitrax throttle? It would be interesting to see if the DCS100 command station replies to that request with "busy". ...
Hi Don, ... I had some problems to find Your comments. I tried to sort that out. ... Sure I would. But from Your description there is a difference whether You...
Greetings: Another question from the new guy on the block (who loves the program by the way) I have engine with a Lenz 1024 motor control decoder and...
John - The only foolproof way to read or write addresses is to disconnect. However, if you program different 2 digit addresses in both decoders - while they...
Rob, I haven't owned an MS100 for a while but I seem to recall it came with its own cable. I'm sure one end of the cable had a ferrite coil on it and that end...
Rob, ... First, take out the phone cable! Phone cables are straight through. Pin one on one end is pin 6 on the other. Digitrax uses what most others refer ...
... Your correct in the ideas you have, but I think a little confused on the cable terminology. That is why you sound confused. True: Phone cable most often...
Rob, why do you say EasyDCC is incompatible with Windows XP? I have a Dell 2.5Ghz PC running Windows XP Pro and have my EasyDCC system connected up to it...
When I start Decoder Pro and enter my preferneces it does not create a list of available com ports (WIN95). For giggles I installed it on my Laptop running...
Ill give that a try, but the first XP install I did would not work with it. I now have others and will give them a try Thanks R ... From: Tony Rogers...
Richard, I do not know what to say. Both models had their decoders installed and completely functional. When I tried to read all with the DP everything in both...
