Ken, All I did is copy the example script, added extra lines for the additional points and changed the nameing for the sprog ones. I can post ir required but...
Yet another question. When making turnout icons, do I just make 4 of them (one for each state) similar to the ones in the existing file? Should the naming...
Walter The DCS50 can read back CVs Richard P. Stamm Modeling the Colorado Midland in 1905 http://home.comcast.net/~rstamm4/ ... From: "Walter Thompson"...
The Empire Builder does not read cvs but the DCS-50 does But not my DecoderPro. ... From: jmriusers@yahoogroups.com [mailto:jmriusers@yahoogroups.com]On Behalf...
... Name them anything you want as long as it means something to you. You can select them in the panel pro editor with the change icon command from the turnout...
Good tips, thanks Jim. I think that's all I need to know to create them. Ken ... From: macintoshtrainman To: jmriusers@yahoogroups.com Sent: Thursday, December...
Hi Ken, When you decide to make your own icons, you can make whatever you need. In the case of the switch icons, you actually need to make three of each, Open,...
Hello Steve I think this is what I'm talking about The logical connection is made by Panel Pro when you add a turnout and specify the turnout number. I have...
I got the same problem with some NCE and Lenz decoder, if it’s the case just put a 5k to 10k resistors between the 2 rails when you want read cv and make ...
14430
jmriusers@yahoogroups...
Dec 1, 2005 5:14 pm
====================== HOW to ask your question ====================== One of the most common questions about JMRI is "How do I get it to work?" This isn't...
... specify wheter to use direct feedback or one sensor or two. If you use sensors the become inputs from the DDC hardwre that you connect to contacts on the...
Hello Moderators Thanks for this info. I should have known there would be more to it. I have gotten a lot of good help so far building the panel. This is the...
... sure doesn't USUALLY help to get feedback from windows 98 users with a com 1 port. The more info the better. Jim ... really a problem with JMRI itself in...
... That's true. To do ops-mode reading, you need to have a BDL-168 & RX-4 attached (the received data comes back via Digitrax transponding); the command...
... "All" is pretty big, because the entire JMRI library is available. That is documented here: <http://jmri.sourceforge.net/JavaDoc/doc/> There's so much of...
I have a BDL-168 and RX-4 attached. When I start OPmode programmer I select the engine from my roster. Then I select comprehensive format. I open the...
Hi, can I say that the series of questions and answer to this topic has stirred me into having a go at Panel Pro again, especially after visiting the Clinic on...
Nick, I hadn't thought of the upgrade removing custom icons. Thanks for that very important warning. By George I'm learning this PanelPro stuff little by...
As I use Peco track & points, I will be going for their motors where needed. While i have looked at the Toitose motors, its a bit hard to justify the more than...
... There are two places where you can put icons easily. One of them is the distribution directory, which gets replaced when you get a new version. The other...
YES Where is The MANUAL ???? Thank you, Jim Drennan Northwestern Illinois Hobbies / Custom Paint Shop 101Main St P.O. Box 281 Chadwick, IL 61014 (815)...
... Open the "Console" application from the Applications/Utilities folder and see if there are any error messages there. That might give a clue. Bob -- Bob...
The Hoffmann point motors are a good buy, they are slow action motors designed to be a direct drop-in for twin coil machines, and I can confirm that they work...
I recently loaded JMRI on an E Tower5 year old computer operation Windows ME, JAVA 1.5.0_05 (en_us), JMRI 1.6.1; interface Digitrax MS100: DCC system Digitrax...
I have created a panel that controls turnouts and shows occupancy. I would like to proceed further, e.g. controlling signals and locos on the basis of turnout...
