Robert, Ops Mode is not implemented in all extended packet format decoders. I don't think the DN93FX supports Ops Mode programming. Also, taking a careful look...
Bob, None of the ops mode works. I don't own a 400. I will see if my railroad buddy can bring his and come over this evening so we will do the test you...
I have found and so has another person that Decoder Pro throttle functions keys 9-12 do not work above 8 with the Digitrax DCS100 Booster. This is Decoder Pro...
Hi all, new user of JMRI since last Sunday, bear with me I think the definition of function mapping in the TCS T1 decoder is really NMRA compliant, but...
... update for a more current TCS T1, version 28 (according to CV7) a) DecoderPro comes back with no such decoder defined, identifies however TCS via CV8 b) it...
... This is a mystery to me. When I test it, I see the messages that expect to be sent, and I see the right packets on the track (confirmed by a PRICOM...
... Not currently. I'm not sure how hard that would be to add, at least for the specific case of Windows. Can you point me to any hardware docs on the card? ...
I have tried them and found I needed to register. I have twice tried to register and have received no reply. Since you reported it I will wait and see. ...
Just asking the obvious but do F9-F12 work from a DT400 using the DCS100. If not you got a DCS100 that needs the firmware updated and no amount of changing to...
... Bob, The manual for the ISA board we used is at http://www.nudaq.com/download/ACL-7122/A7122Manual.pdf. There apparently is a basic difference in how the...
Hi I have looked at these things, and they appear to be seriously cheap. If I recall correctly you have to manually put the address on the card, and then just...
... The basic problem here is that Java was designed to be portable, secure and hardware independent. What is needed here is direct hardware access on a ...
... wrote: ... Hi Bob The card I have is Decision Products International (Taiwan) MULTI 8255/8253 CARD. (www.decision.com.tw) Brief specs: <Quote> "...8255...
You mention use of a Locobuffer II thus I'll ask if you've set the Baud Rate to be the same speed for the LB II and within Decoderpro? Are you using a USB to...
... Hi, What were the results of the two different tests given in the manual? Both green lights on? Does the red activity light blink when you mess with a...
Dick The green lights are both lit as they should have been. The red light blinks when I mess with a throttle. The com port in decoder pro is connected to com ...
I have not set any baud rate. How do I do that? I have the USB to serial cable because my computer does not have a serial port. [Non-text portions of this...
... I see someone else has already addressed this, but your question above led me to do something I've been thinking about for a while. I've added the...
... I think this may have already been done: <http://www.geocities.com/Juanga69/parport/> <http://www.geocities.com/Juanga69/parport/ParallelPort.html> It...
Bless You for doing this. I am a member of the Digitrax list but I have had to stop incoming emails from that group because no one has ever taken the time to ...
... OK, The blinking red light tells you that the LocoBuffer-II is listening to the LocoNet OK. The USB port number gets set by Windows magic. (or whatever) If...
... Hmmm... good find. Well it looks like they have done the JNI bit which means we don't have to do battle with MS Visual Studio and this could easily be...
"Has anyone got any source code to drive the 8255 with all the port setup etc?" Alex, Sorry but all my source for 8255's was lost when I finally tossed my CPM...
... Looks to be pretty straight forward. In my early days with micros it was a Intel 8085 with the 8155 I/O chips. ... Let's hope it is not PCI then... :)) ......
