I'd like to be included in the beta testing of the 090LC . I recently purchased an Easy DCC system along with some SoundTrax decoders. I tried using the 100LC...
Phill, I use SoundTraxx and EasyDCC too and found that need to wire a resistor in series with the programming track leads. This is covered in the manual, but ...
Thanks, the 100 Ohm resistor did indeed fix the problem of unreliable CV reads. ... From: "Mike Davison" <davison@...> To: <jmriusers@yahoogroups.com>;...
I have been able to get DecoderPro running on Win98SE with zero problem. However, moving to Redhat 7.3 I am getting some runtime exceptions. I followed the...
Could you try an experiment for me? Edit the script you're using to start the program (e.g. DecoderPro.csh) and add the "-noverify" option to the single...
... This is fixed now, thanks for pointing it out. Those of you taking the code from CVS and recompiling the program can get it now. I'll try to put out a...
I've just uploaded the 1.1.3 test version of JMRI DecoderPro. It's available for download at: http://prdownloads.sourceforge.net/jmri/JMRI.1.1.3.exe This the...
Bob - I'm downloading it as I'm writing this note. A feature I'd like to see would be the ability to print the CV page - perhaps with a customizable format....
Bob, I downloaded and installed the upgrade for Decoder Pro / EasyDCC. The online part worked OK - as does all the rest. There is one annoying side effect of...
Hi All, I thought this program sounds excellent so am just D/L the prog and Java whilst reading through the guides etc. Suddenly had a nasty thought :-) My...
Bob, I agree with Bruce and Gerry that a paper print out would be an excellent feature. I have been using DecoderPro for a while now and am really pleased...
... I don't know, but I suspect not. DecoderPro doesn't have any ZTC-specific code in it yet. I'd be happy to look into how hard that would be to add. Could...
... I've not looked at Java printing in any detail, but I think it's pretty easy to print specific things, e.g. existing parts of the display. Would you be...
... Which DCC system are you using for this? It sounds like the NCE or EasyDCC systems, where the program goes in and out of programming mode for each CV....
... Wow. That's quite a recommendation! ... Could you point me to a sample of what that printout looks like? And could you describe what you like about it,...
... And ... Bob, I just scanned in a 3-page sample output from one of my locos and will e-mail these directly to you for review. As you will see, it has a...
Gerry, I use EasyDCC and sound decoders too (although I only _wish_ I had 20 decoder-equiped locos!). As near as I can tell, the behavior you're describing is...
Group: This on-off situation during programming is also standard on NCE. When the programming track is activated, the main track power is shut down and when...
... Bob, I use EasyDCC (V418). I tried a program called Decoder Tools (www.stormyacres.com) and it did the same thing but an email to the guy there and he was...
... Hi Mike, The same thing was happening with the software from 'Capt Kirk'. He has Easydcc but the layout was in a different room when he was using the ...
Bob, I thought I'd give DecoderPro a real workout and install it on a newly formatted PC. So, armed with my DOS FDISK and Format utilities, I wiped the disk on...
I keep getting this report when I'm viewing the LocoNet: General Sensor input report: contact 955 (DS54 119 ch2 SW input) (BDL16 11 C4) is Hi. It keeps...
... Some LocoNet attached device is seeing it's input change from active to inactive and back, and is reporting that. Depending on what you've got hooked up,...
Does anybody know what he's sending to the EasyDCC command station to have it program without turning off main track power? DecoderPro sends: M to go to...
Thanks! How's performance on that 200MHz PII? And how much memory does it have? I've heard varying things about the minimum needed for the program to run...
Although I understand the overall issues, the details are over my head at the moment. But I wanted to say thank you to all for thinking and working on this...
