I have been using the FT1500M with the special cables for it to run node 8900 for some time now. The radio has died and it looks like it may not be repairable....
Hello Gopal, You can check the pin outs on the Yeasu FT7800, 8800 and 8900. The data port are 6 pins which are standard on all the above radios and a most ...
... the ... unless ... it. ... I agree with Dave. If you are going to use a simplex node, then I suggest using a PL. This way the squelch is never the issue...
Hi all, Just a hint with routers in case you didn't know when using two routers in series, I will call it or double routering down, you can't assign the same...
The hard disk was changed. I requested a reload yesterday, but I guess that it never happened. Is that the place to restart? There was a ticket number, but...
I want to start preparing my node by compiling and installing the IRLP software but can't seem to find it. I saw the CentOS order page but I'm not intending...
Hi Chris. To use IRLP you will need to order an IRLP card. The IRLP software is self-installing and doesn't need to be compiled. Installation is trivial and...
... board. ... That is fine. If I order the board then the distro will come with it. Does that distro include the source? CentOS will not fit on a 256M ...
... No, not unless you choose to pay extra to have it shipped to you on a CD. Refer to the online order form. ... The IRLP distributions are text only and...
Gopal (VU2GMN?) wrote... ... I'll take it off your hands - hi! ... I don't know of any current single-band VHF/UHF radios that have the 6 pin mini DIN...
Will W4WWM wrote... ... Actually, the FT-1500 has the 6 pin mini-DIN on the back, and the mic connector on the right side uses an RJ-11. Keith VE7GDH Node 1148...
... As a "rule of thumb" I would not use the (1200 bps) TX data pin on the 6 pin din connector. The reason why is that most radios with a 6 pin din connector...
I'm helping a friend with a project and thought I'd tap the collective knowledge base here. Yes, this is IRLP related, just not quite there yet. Q: What's the...
Head to www.fab-corp.com and let them know you are a ham. Not only will they help you out, they might cut the costs a bit as they are hams into experimentation...
... <---I use a pair of Air802 AP-G300 radios with built-in POE (no feedline concerns!). http://www.air802.com/product.php?productid=17196&cat=413&page=1 They...
<---I use a pair of Air802 AP-G300 radios with built-in POE (no feedline concerns!). I meant to say I use 3 of 'em http://www.ah6le.net/ah6le_new.bmp Ken ... ...
... If the path is good, a couple of 10dBi patches will do the trick. I setup a link over 500-600' using a couple of 10dB patches and 30mW radios. Path was...
... Here is the statement from the Ref9200 policy page (which has been adopted by many other refelctors) Special Note for Operators of Simplex Nodes Monitoring...
... You could do: 1) a couple of access points and configure for point to point (best if the single antenna style). 2) stuffed inside an outdoor enclosure,...
ISP is Qwest Modem is a Actiontec GT701 I think I need a Static IP address form Qwest to put this in Bridge. Because the dsl modem needs a User name and...
Ok. This would be nice If my DSl Modem had 2 ports one for my apple router and one for the IRLP computer. The first DSL Modem from Qwest is a Actiontec GT-701...
Please inquire with Quest. Static IP was not required for bridge config when I had DSL using a different ISP. Jim WW4M ... like you have 2 routers between your...
Hello All, I have just re-installed my node onto a new PC box after the last one died. The reincarnation seems to have gone well with the software transfer, ...
... Putting the modem in 'bridge' mode makes the modem 'dumb', your router now does the logon to your isp for you, most dsl modems allow you to do this. Here...
Here are the numbers from the New Years party yesterday on Reflector 9200... Total nodes participating: 253 (see note below) Maximum simultaneous nodes: 104 ...
I was on sprint when I put in my node. I had the same problem. I put the modem in bridge mode, then set up the router with proper name and password to log me...
Ok, here's the short, correct answer: The ActionTec DSL modem by default is connecting to Qwest via PPPoA. I would expect you have the ports forwarded in the...
Note that the GT700 series is a modem and a router and a switch and optionally a wireless access point. There is a GT701 (not wireless, i.e. without an...
... I bet Actiontec would consider "notorious" to be "responsive to customer need" <grin> The ActionTec used by Verizon FIOS is even wierder, not only are...
