Which timeout are you hitting? The COS lockup, PTT lockup, or activity timer? There are three. The COS activity timer is 3 minutes The PTT activity timer is 4...
I have a fault with our node 6464 we can dial into other nodes and they can here us but we can not here them, we also get the anoucment on our end when the...
Jason, Your node is behind a router, and that router has port forwarding information set in it to allow your node to work behind it. What has likely happened...
Is there a way to allow the DTMF to pass through the to another node to control another part of a system. Is there a special script that will make this work. ...
... Hi Mike, DTMF_REGENERATION=YES in the /home/irlp/custom/environment file (default it's set to no) on the remote IRLP node will cause IRLP to regenerate any...
... When configured for _FD operation, I recall there being a way to disable regeneration and allow DTMF pass-through if both nodes agreed on the method. I...
Actually, there is (or should be) and unkey between the initial send and the regen. If not, you can always add delay into the dtmfregen script. Dave Cameron ...
... Hmm.... if it's there, I've never heard it, but I wasn't listening all that closely either. :-) That would "fix" it, just fine. Cool. -- Nate Duehr, WY0X...
Hi David, I think that if the audio is lowered the DTMF will work but the voice audio cant be herd. I have my embedded node hooked to my RLC-4controller with...
... The DTMF_REGEN dtmf comes out at "100%" I think by default, or it's settable somewhere... Dave may have added that later on, I can't remember... 50% of...
HI David, I just spoke with Chris K7UND in Oregon and he is resetting his node. I belive the problem is with his side since he can control my embedded node ...
BCC'd Steve @ Link Communications Hello Everyone, Mike and I have been doing a BUNCH of testing and we have it narrowed down to this as our issue. The first...
YEA!!!!!! That did it Dave! Now, there is an unkey before a re-key and now the DTMF is working GREAT! Thank you so much for your attention to this. Chris...
In addition to standard IRLP functions, I am interested in having my embedded controller route APRS data and AIS data to servers on the internet (Igates)....
... There's a package for "normal" IRLP nodes that sends APRS "connected/disconnected" messages to the APRS servers, but two things: 1. I don't know if it will...
... The new system no longer uses perl so should work on embedded nodes. We were experimenting with embedded nodes a while back, but don't recall if it worked....
... Hi Nate. I thought that package was for only reporting the status of your IRLP node and not for collecting APRS data from a TNC via the serial port on the...
Here is the current status of my little project. I downloaded to my windows xp machine the "spu.tar.gz" file from www.coaa.co.uk Then I copied it over to the...
HI David, The fix for the DTMF works great but K7UND's node will not keep the settings if the node happins to reboot for some reason. I am trying to figure out...
... Is his an embedded node too? Remember, they run from RAM disk and you have to issue the command to write the RAM disk to flash or they come back with...
Hi Nate, No his is the normal node, just a computer. The Echolink is working now. I think David logged in and made some changes. All is working great. Mike...
Craig WD5BDX wrote... ... The best place to place "add-ons" would be in /home/irlp/custom. ... It is? As far as I know, the serial port isn't being used. ... ...
All I did was log in and reset the tbd process. Dave ... David Cameron - VE7LTD IRLP System Designer - http://www.irlp.net ... From: "Mike Mullarkey"...
Hi Dave, Thanks again for the help. I am slowly learning all the things that need to be rest etc. Mike Mullarkey (K7PFJ) 6886 Sage Ave Firestone, CO 80504 ...
... Mucho excelente, Senor! :-) Heh heh... having fun with D-STAR here, got an ID-800H... running this thing through the front-panel is a pain in the ass, but...
... I forgot for a moment that the embedded node has a keyboard, mouse and VGA port. I actually haven't used the serial port for the console. This brings up...
I checked my log today and noticed it was there for Jan, Feb, March with no April and May 18th only as I rebooted the node. Anyone else experence this? Also...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
