No, and there is no real reason too, as that is essentially what is done each time the flash_sync is run. The drive in the embedded node is a flash drive. The...
764
k7iou
nospamk7iou
Feb 17, 2008 5:00 am
Dave, is there a script to back up the embedded node to a thumb drive? Thanks, Dave k7iou 3033...
763
David Cameron (IRLP)
ve7ltd
Feb 15, 2008 4:28 pm
The problem is that when configuring your node, I forgot to change some of your settings to not be the ones I use to test with :) You will have to edit the...
762
Greg Peralta
camperguy77
Feb 15, 2008 4:16 pm
Hi Dave: My embedded system is working great, however when I used echolink from my PC to connect to my node I get a "connected to VE...." message, I can't...
761
David Cameron (IRLP)
ve7ltd
Feb 12, 2008 8:05 pm
/etc/rc.d/rc.inet1.conf Dave Cameron...
760
Don
donmor46
Feb 12, 2008 8:01 pm
Can someone point me to the area in the embedded node that is the same as the regular node /etc/sysconfig/network. Thanks Don VE7EDA Node 1811...
759
nospamk7iou
Feb 12, 2008 4:52 pm
Gentlemen, I purchased a used node and have 2 questions. Where can I download commands for the Slackware Linux 10.2.? Can I backup my node with a thumb drive?...
758
Jim
n7hqz
Feb 11, 2008 1:13 pm
Hello, I am running my embedded node over a wifi link using Tranzeo equipment. I have a 5.8 ghz link with a 25 mile link shot, 3 foot dishes on both ends. Work...
757
David Cameron (IRLP)
ve7ltd
Feb 11, 2008 5:38 am
This is the DTMFPREFIX variable in the /home/irlp/custom/environment file of ALL nodes. Uncomment the line, set it to what you want, run a flash_sync (if on an...
756
nospamk7iou
Feb 11, 2008 5:33 am
I posted this early this morning but it didn't post. Is there a script for adding a prefix for connect and disconnect of nodes? We are running 2 IRLP's on our...
755
Stephen Johnston
ve6cyr
Feb 11, 2008 1:46 am
Has any one every tried to run the embedded over a wireless net? And if so how was it done? IRLP Node 1300 EchoLink Node 74852 Steve Johnston VE6CYR Connect...
754
Keith VE7GDH
ve7gdh
Feb 9, 2008 4:07 am
Bob WB4APR passed this information along... * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Please share this web page with all IRLP node...
753
Don
donmor46
Jan 15, 2008 2:49 am
Rich. Connect to the stn or ref that you downloaded the wav file for and it will play if in the correct folder Don VE7EDA Node 1811 ... to download custom wav ...
752
Rich Sytsma
richsytsma
Jan 15, 2008 2:40 am
I down loaded a couple files what has to be done to get them to play? Rich Sytsma N9GPY node 4960 4961...
751
David Cameron (IRLP)
ve7ltd
Jan 13, 2008 6:51 pm
I have posted the audio files on the irlp.net website. It is a live system, so changes are instant. Here is how you get them onto your embedded node. su -...
750
garyp609
Jan 12, 2008 11:20 pm
I have an embedded node and would like to know if there is a way to download custom wav files for specific reflectors to play on my system. I know that I have...
749
Ken Arck
ah6le
Jan 11, 2008 6:31 pm
... <----The RC210 does not have its own on-board CTCSS encoder (or decoder for that matter). Our RC810 does however. That being said.....the RC210 *does*...
748
James Nessen
nessenj
Jan 11, 2008 6:22 pm
There is also a yahoo group setup for the rc210 controller, you might want to ask over there: http://groups.yahoo.com/group/rc210 Jim / K6JWN...
747
Nate Duehr
wy0x
Jan 11, 2008 5:06 pm
... Mike, Look in the log file: /home/irlp/log/messages To see what it's doing. Also check your environment file and see what your timeout values are set for. ...
746
Nate Duehr
wy0x
Jan 11, 2008 4:59 pm
... Have you talked to Ken Arck at Arcom? I know he himself (the designer and seller of the controller) runs a few IRLP nodes, so I'd think he would be able to...
745
Mike Mullarkey
k7pfj
Jan 11, 2008 4:43 pm
David, Lately I have been noticing that my node 3003 is disconnecting from both a reflector as well from a node to node. I am mainly connecting to node 3153 ...
744
vk4mih
Jan 11, 2008 1:25 pm
Can anyone tell me if there using a RC210 repeater controller with IRLP link radio and if this controller will encode ctcss to open the link radio on the IRLP...
743
dcameron@...
ve7ltd
Jan 10, 2008 1:52 am
Instead of going to a larger flash drive, put another one in the secondary IDE slot, or add a USB thumbdrive. There is more to it than just adding storage...
742
garyp609
Jan 10, 2008 1:24 am
What is the easiest way to clone to a bigger flash drive? 73's Gary K2ACY Node 4883...
741
Jeff Dale
eter4_imu
Jan 8, 2008 10:03 pm
You may want to fill us in on what your asking Are you a node owner who is trying to setup his node? Are you a user who is looking for more information on how...
740
jasper griffith
kb2toh
Jan 8, 2008 3:46 pm
i am ready to be on irlp so ____________________________________________________________________________________ Looking for last minute shopping deals? Find...
739
dcameron@...
ve7ltd
Dec 18, 2007 3:27 pm
You should update the IRLP status page info as well. Dave Cameron ... David Cameron - VE7LTD IRLP System Designer - http://www.irlp.net ... From: "garyp609";...
738
garyp609
Dec 18, 2007 2:18 pm
Besides replacing my old callsign with my new callsign in the config files is there anything else I need to do?...
737
Craig
craiginhouston
Dec 13, 2007 3:27 am
We are going to try an experiment of patching the astronaut demonstration described below to IRLP Reflector 9010 tomorrow morning while its in listen only...
736
Keith VE7GDH
ve7gdh
Dec 10, 2007 12:36 pm
Mike K7PFJ wrote... ... Seeing as the weather script can't be installed on embedded nodes, how about a central server that could create the audio files? It...
