I searched here but could not find an answer. I have a new embedded node #4114. It's conected to a repeater via a UHF link. I would to enable a courtesy...
Hello All IRLP Node 1111 is now active on our 2 repeaters in Fort McMurray. It is directly connected to a CAT400 Controller on our 147.000+ VE6TRC machine with...
http://www.irlp.net/embedded/Embedded_Info.pdf I have updated the above file, which is used as the installation document for new embedded nodes. I have added a...
I in the process of using the fan_ctrl script for aux3 I have put the script. And edited the three lines in rc.irlp I put the script in the node at:...
Hello, I'm just wondering if there's anyone out there using a Kenwood TM-D700 as their radio with the embedded node (and embedded cable) and if so, what COS...
The issue is a forced block of updating the reflector audio files. This was put into place to protect the embedded nodes against a very large reflector WAVE...
My ISP changed IP addresses (dynamic) and I can't find it. How often does host.net update, or is there a way to find the IP address? Thanks Don WB5EKU nodes...
I am having a DNS problem that has been discussed before. I entered the correct DNS address (local ISP's DNS server) into the file /etc/resolv.conf and also...
RE: Embedded Node only I have two nodes. Both have been working great for at least a year. One for almost 3 years. About a year ago, I turned the morse ID...
I have a mobile node in my 4 wheel drive, that does not have a keyboard attached. I have to actually switch it off when I have finished using it. Can anyone...
Hi there I recently converted my working IRLP node into an EchoIRLP node upon doing so I have audio both ways on the IRLP side working fine. My audio on the...
How do you get your embedded mobile IRLP node to report its real-time position to the APRS servers over the 3G? I was successful today hooking a Germin 18...
Not being familar with the install process or how Linux works, I have some questions about swapping SSD. Given: Say I have a working embedded node. Say I want...
Hi All, I have just installed the script below. I call it with a "0" If not connected it says "link clear" good. If connected either IRLp or EchoIRLP it...
I have found one similar question that was 4 to 5 years old so I'm asking this question again. Is there a way to add a weather script to download and play a...
I know most of you with probably think that this is a no-brainer, but I have not managed to find all the relevant information together in one place. As I am...
Hi everyone. After months of having the node in the box (Long story)I finally got it up and running and it seems to run fine. I had some audio issues but think...
Is it possible to use CentOS 6? The reason I ask is I am trying to use a intel based mother board but the current 5.4 does not work properly with the built in...
I have a couple of IRLP nodes. One of them is in a 19" rackmount, which I used in my vehicle. This is a Dave Cameron embedded node. I'm thinking about buying a...
I have been given an embedded drive module that I have installed on Node 6482, when I do a shutdown -h now, it goes through the shutdown procedure, and the...
I'm on a vertical learning curve with Linux. How do I setup a status check on my node with a DTMF tone? Many people transmit a 0 (zero) tone to check IRLP...
A few days ago, we had a local and very violent thunder/lightning storm. Naturally, I switched everything off, and disonnected all the antennas. During the...
My ISP replaced my old cable modem with a combination modem/router The SMC D3GN. I like it because it is also a wireless router (not for the node computer...
Have searched this question within the group without any result. If it has been addressed please refer me to the relevant message. I have been asked by two...
What happens if to custom audio file is deleted? I want to put our node back to saying just the node number when it connects and disconnects. And how would I...
Hi, trying to set cron jobs for 5469 disconnecting/connecting reflector at night time. my custom.crons looks like: # Update EchoIRLP filesystem from EchoIRLP...
