I have installed the new 2gb flash drive obtained from Dave VE7LTD but when I type in flash_sync it does not run and there is the message "command not found"....
Hello all, does anyone know how to add a prefix for the dtmf when connecting to a node and disconnect? I have a new embedded node I cannot put on line due to...
Tim VK3MIT wrote... ... Just guessing, but I would assume it would be to send a "tweet" when the node status changed... connected to XXXX, disconnected, etc. ...
I just installed the "IRLP-tweet" script from the files area of the IRLP group. Unforunately, the embedded node operating system does not have the curl...
It usually happens if the node is not connected to the internet when it is powered up. Either that, or as it says, the DNS servers are not setup correctly. ...
For those of you who want to use USB keyboards on your embedded IRLP nodes, you are in luck! I have managed to find the correct sequence of drivers required to...
Will a new embedded node with a DOM allow me to modify a configuration file and save the new image to the DOM? Is CentOS OS the stripped down embedded node...
Dave I think I will order a new embedded node as my insurance will cover it. I am curious as to the damaged node since the image will not support USB, can an...
K7IOU - Dave (3033) I had a lightning strike and it took out bunches of stuff. We're trying to see if the imbedded node is still operational. I'm able to shell...
Is the image for an embedded IRLP node available to download somewhere? I have several IDE Disk On Modules that I would love to install IRLP to so that I don't...
I am going to be using the 440 side of a kenwood tmv-71a and an embedded node for a simplex set up on 445.450. I am wondering what the cos jumper needs to be...
I was fiddling around with EchoIRLP today and went to restart tbd using "service tbd start" as root (after having shut it down, obviously). I got "service:...
I searched here but could not find an answer. I have a new embedded node #4114. It's conected to a repeater via a UHF link. I would to enable a courtesy...
Hello All IRLP Node 1111 is now active on our 2 repeaters in Fort McMurray. It is directly connected to a CAT400 Controller on our 147.000+ VE6TRC machine with...
http://www.irlp.net/embedded/Embedded_Info.pdf I have updated the above file, which is used as the installation document for new embedded nodes. I have added a...
I in the process of using the fan_ctrl script for aux3 I have put the script. And edited the three lines in rc.irlp I put the script in the node at:...
Hello, I'm just wondering if there's anyone out there using a Kenwood TM-D700 as their radio with the embedded node (and embedded cable) and if so, what COS...
The issue is a forced block of updating the reflector audio files. This was put into place to protect the embedded nodes against a very large reflector WAVE...
My ISP changed IP addresses (dynamic) and I can't find it. How often does host.net update, or is there a way to find the IP address? Thanks Don WB5EKU nodes...
I am having a DNS problem that has been discussed before. I entered the correct DNS address (local ISP's DNS server) into the file /etc/resolv.conf and also...
RE: Embedded Node only I have two nodes. Both have been working great for at least a year. One for almost 3 years. About a year ago, I turned the morse ID...
I have a mobile node in my 4 wheel drive, that does not have a keyboard attached. I have to actually switch it off when I have finished using it. Can anyone...
Hi there I recently converted my working IRLP node into an EchoIRLP node upon doing so I have audio both ways on the IRLP side working fine. My audio on the...
How do you get your embedded mobile IRLP node to report its real-time position to the APRS servers over the 3G? I was successful today hooking a Germin 18...
Not being familar with the install process or how Linux works, I have some questions about swapping SSD. Given: Say I have a working embedded node. Say I want...
Hi All, I have just installed the script below. I call it with a "0" If not connected it says "link clear" good. If connected either IRLp or EchoIRLP it...
