Anyone that has parted out a number series Lo Boy have a Speed Change/Throttle lever they can part with? This is the lever that pivots on a pin on top of the...
Dear Members A BRAND NEW Page of Fresh Freebies was just added ready for Monday 3rd November. Visit Now! You are sure to find something of interest, and they...
The new 'Sneakers' finally arrived !!! See 'Photo Section' for '184 A New Set of Rear Tires'. Front set of tires are 5:00 x 12 Tri-Ribs for #50 Snow Thrower &...
Just curious, What did you give for the rear tires? They look nice on your tractor. I see that you have spacers on also. What size of spacers do you have on?...
... The spacers are the 'factory' iron originals (about 2-3/4" - I think). My son is going to order the new chains this week. And, oh yes - in the background...
Dear Members A NEW Page of great Freebies was just added ready for Monday 3rd November. Visit Now! If you would like a veritable 'mountain' of free-stuff, take...
I own a model 185 equipped with a Woods 59 inch belly mower. The primary use is mowing grass. The machine starts easily and works well. Over the past year I...
Yes, you are probably due for rings, but the reality is that it probably won't make all that much difference in your performance. I have half a dozen tractors...
I side with Mike as to what you will gain with a set of rings. In my opinion, I wouldn't open up a C60 engine unless I planned a full blown rebuild. Once you...
I recently purchased a Pertronix #1442 Electronic Ignition for $68.00 plus a little under $7.00 Shipping (they charge actual UPS cost) from w.helmarparts.com....
Thanks, Dale. That is good to know. I went to the Website <www.helmarparts.com> an typed "Pertronix" into the search window. The 1442 kit came up on the third...
Dale, Mike, I purchased the Pertronics kit from Helmarparts.com. Recieved shipment on time, about five days, installed it the next day and man what a...
All my tractors have IH distributors, but the parts book suggest Prestolite distributors were also used. Does the Prestolite use the same 1442? Before...
Mike Sloane <mikesloane@> ... Yeah, Mike - I was thinking of you when I made the post; with 10 or 12 to buy - $$$$ - Check out their other stuff, everything...
A NEW PAGE of FREE STUFF was just added ready for Thursday 6th November. Visit Now! You are sure to find something of interest as there is something for ...
My experience is that these simple engines run much better if you freshen them up. 1. Check the cylinders for wear. if under 10 thousands wear new rings cut to...
The only thing I would take issue with is bumping up the oil pressure. The C-60, being essentially a WWII era F-head engine, will run just fine on as little as...
I believe that Pertronix makes a kit for the Prestolite distributors, but it is NOT the 1442 version - the distributors are very different inside. As a rule of...
I HAVE 2 184`S ONE RUNS WELL/LOADER THE OTHER HAS A KNOCK IN THE MOTOR BUT A CREEPER DRIVE. MY QUESTION IS DO I NEED TO DRAIN THE CENTER SECTIONS OF THE ...
Mike and or MJ, While you are on the subject of engines; For most of the Farmall tractors (begining with the 'A' on up), IH offered two 'High Altitude'...
... If it was me, I would drain the fluid - it should be changed every 250 hours anyhow. I recently did a brake job on a 184 and the drain plug was so buggered...
The creeper is independent from the transaxle, I bought a 184 that had water in the creeper assembly. Since the creeper doesn't have a drain plug, I had to...
I keep my fields mowed with my 154 with a mott flail mower. The last 2 times I have mowed, the engine has started to skip under a load. It would run fine for...
... that had water in the creeper assembly. Since the creeper doesn't have a drain plug, I had to remove the creeper to get the water out. It has a 1/8" drain...
A NEW PAGE of FREE STUFF was just added ready for Thursday 6th November. Visit Now! You are sure to find something of interest as there is something for ...
Since I didn't see a reply to this message, I will give it a shot. While the coil sounds like the most likely candidate for the source of "skipping", or...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
