Thanks Glen Eventually found it in the manual...... Get your Port B up and running again ?? Frank ... From: Glen Ferguson To: homevision-users@yahoogroups.com ...
Guys I would like to monitor PC's status using something like PING, however if the PC hangs and no ping response is received I want to use HomeVision to send...
Although my PC nevers hangs using Linux :-) I do have simular requirement as you have. When PC isn't alive I want the power OFF. So I have an CM11 computer...
Ruud
ruud3@...
May 6, 2005 12:28 pm
8359
Hi Glen, Frank posted this question on my behalf. I to read this in the manual but I power HVPro off insert a pre-manufactured stereo to stereo 3.5mm lead,...
Steve, Do you have anything connected to the other end of the cable that's plugged into HomeVision-Pro? If not, then the plug is shorting 12V to ground (which...
It expects to receive a signal that's high (usually 9V or higher, although 5V should work) when the IR signal is present and open (or ground) when not present....
Is anybody controlling a UK TiVo with infrared using HomeVision? If so did you learn the codes or do you have a list of the "Device" and "Key Codes" ? HV...
Steve Before I solder anything or attach anything to HV I check the plugs with a multi-meter. Buzz out the tip and centre band connectors to ensure there are...
Yes indeed rod it is definitely the RX port. I already have a plug in the TX port for FirM! I don't blame you for asking we all make silly mistakes like that,...
MessageHi Steve If your using a male to male mono lead from FirM out to HVPRO IR IN then you will short the 12v on HVPRO to gnd..... Frank ... From: Steve...
I understand that Frank. I was thinking of making up a Mono to Stereo patch lead to see if I could send IR from FirM direct to HVPro socket rather than using...
MessageHi Steve Its bloody strange I just purchased a new stereo jack with no lead on it and it doesn't short HV out. So it must be the lead I was using even...
There was a time you could get quality components, now its all got to be made at the speed of light......... I hope your not thinking of getting your switcher...
Thanks for the chips Frank, port b works fine now. I remember you discussing using C-bus with HV sometime in the past. I am about to substantially renovate a...
I remember you discussing using C-bus with HV sometime in the past. I am about to substantially renovate a new house and was considering my lighting solution....
Glen Maybe Dynalite could be a better option than C-Bus. The Dynalite people purchased a HomeVision from me to do some integration work and released a software...
Rod ... done ... There is a public release version of the cbus available from the website ..... http://www.cbus-enabled.com/ ... Not so......I sourced my kit...
Hi All Anybody controlling Tivo via Homevision ...??? any issues ie able to move up down the menus ok.... Im asking on behalf of Steve Jones.....It seems the...
... The Tivo code looks like the NEC1 code, except that a real NEC1 code consist of four bytes containing the device code, the inverse of the device code, the...
Hmmm... I posted this message earlier here but it never showed up... I am new to UPB and to HV Pro - so this might be a silly question. I want to read the...
I am installing UPB switches with my HVPro and so far am very impressed. However, I need some help (I'm new with both systems). I can control the lights fine...
I'm desperately seeking advice and recommendations on how to fix communication problems with my Homevision unit. My electric setup has a main and sub breaker...
Hi Schelte ... Dont know if it can be done ..but if you hold say the Menu up Button down that it works as normal ie continually goes up thru the menu ...but i...
Hi Can you offer any help with getting Flash Movie to work correctly with HV Pro software/Controller. My Movie files are located on the same laptop and in the...
I'm not familiar with the use of sub breaker boxes and multiple repeaters. ... multiple repeaters might cause problems. However, I'd defer to the repeater ...
Paul, The "Export" command should be creating the "HVConfiguration.txt" in the main HomeVision directory. If you don't see it there, do a search and see if it...
Thanks Craig The "Export Schedule is actually creating two files 1 = a HVX file 2 = HVConfiguration.txt file Both these files are being placed in the HV...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
