homevision-users : Messages : 8198-8227 of 12350

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

8198	I' cann't get the control software to run a make from the Control drop-down menu. I receive a message saying controller error at the bottom of the screen. All...	Mark Withers withers@...	Mar 1, 2005 7:00 pm
8199	Does anyone know what Controller error 52 means? Thanks Ron...	Ronald Gross ronrite1	Mar 1, 2005 10:26 pm
8200	Don't know which model you have but in the Pro manual (assuming it is a decimal number, which it should be) it says a Self Test Failed. If it is a hex number...	Dave Yeatman dyeatman1	Mar 1, 2005 11:06 pm
8201	It sounds like a self-test failed. You can use the Status Screen under the other menu to read the status. If a self-test failed, there will be a button to...	Craig Chadwick csi3	Mar 1, 2005 11:56 pm
8202	Ronald Page 317 of the manual says it is "Set if any self-tests fail". Rod Stephens Digihouse (Aust) Pty Ltd 0414 379 079 ... From: Ronald Gross...	Rod Stephens rlstephens2000	Mar 2, 2005 12:08 am
8203	I have a HV Pro version 3.42 and I am currently having a problem reading the temperature from a DS18S20 digital sensor. When in the configuration menu, I can...	homevis2	Mar 2, 2005 6:13 am
8204	Have you moved the sensor from the single drop port to the multi- drop port after configuration? ... I ... some ... the 'Status ... this...	Jon Welfringer jwelfringer	Mar 2, 2005 6:27 am
8205	I'm not sure why you're getting error 118, but a value of 119 is actually 69 degrees F. The temperature values have 50 added to them so that they can indicate...	Shawn Boyle s_boyle	Mar 2, 2005 11:53 am
8206	I have not changed from single drop to multi drop yet. I only have one sensor connected at this time. I will try that later today. I did not realize that a...	homevis2	Mar 2, 2005 7:44 pm
8207	Thad, I assume you have only defined one sensor on the Digital Sensor Configuration Screen, right? If you use the "Clear Error Message" command from the...	Craig Chadwick csi3	Mar 3, 2005 1:01 am
8208	Craig, I only have one digital sensor defined and connected at this time. I used the 'Clear Error Message' comand. The error always returns. I have connected a...	homevis2	Mar 7, 2005 6:41 am
8209	I had a similar problem to this! Try and add the same sensor address to the next line in the "Config temp sensors screen"! Then set up another variable to see...	Steve Jones steve_stealt...	Mar 7, 2005 8:21 am
8210	Steve, you've hit the nail on the head! Here's what's happening. The DS18S20 sensor takes longer to respond than the older DS1820 did (you'd think newer parts...	Craig Chadwick csi3	Mar 8, 2005 12:42 am
8211	Message http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=5757987608...	iihcgm iihcx	Mar 8, 2005 7:08 am
8212	What I would like to do is lengthen the time before my answering machine answers the phone. Maximum setting is four rings. HV already detects when the phone...	Frank Herron herronxry2004	Mar 8, 2005 10:32 pm
8213	Frank, From your description it sounds like you do something like: If EVENT: Phone rings Then Load Timer #0 (Timer 0) With 0:00:12:00 And Start End If Things...	Schelte Bron scheltebron	Mar 10, 2005 7:28 pm
8214	Hi, I'd like my HomeVision to be able to monitor for X10 extended codes. Are there any power line interface components out there that I can use to replace my...	Mun Johl mun_johl@...	Mar 11, 2005 5:50 pm
8215	Hi, I'm looking for a good X10 analyzer. I have the Monterey unit, but find it limiting at times. I came across the LynX-Tools product and was wondering if...	Mun Johl mun_johl@...	Mar 11, 2005 5:58 pm
8216	Mun, No, there aren't any that can be used with HomeVision. Thanks, Craig Chadwick President Custom Solutions, Inc. (a.k.a., HomeVision) mailto:csi@... ...	Craig Chadwick csi3	Mar 11, 2005 6:18 pm
8217	Thank you for the insight. A delay of 0.001 seconds did the trick. Thad ... did (you'd ... Anyway, ... to respond, ... faster than ... schedule with ... that...	homevis2	Mar 12, 2005 5:25 am
8218	Are there any? I'm running 3.3a and I can't find any documentation, although the Help alludes to it....	john_v_h	Mar 14, 2005 12:19 am
8219	John, Under the "Other" button on the Actions Entry Screen Toolbar is a menu item for the Thermostat Data Commands. Thanks, Craig Chadwick President Custom...	Craig Chadwick csi3	Mar 15, 2005 3:14 am
8220	... menu item ... Yes, I know about that menu. I'd like to know if I can issue any of these commands to Homevision via the SERIAL port....	john_v_h	Mar 15, 2005 7:34 pm
8221	John, Sorry, I misunderstood the question. No, there aren't serial interface commands for these "thermostat data commands". Thanks, Craig Chadwick President ...	Craig Chadwick csi3	Mar 15, 2005 11:13 pm
8222	Craig, I just got an upgrade to HV-Pro from you. When I moved my three DS1820 (not DS18S20s) sensors to the new system, they failed to function. It finds them...	Christopher Mills millsspam	Mar 16, 2005 12:59 am
8223	Chris, A couple of hours ago I responded to your private message that addressed this issue. I've attached the same information below. Your new message here...	Craig Chadwick csi3	Mar 16, 2005 1:09 am
8224	Thanks for the response, Craig. Sorry I missed your private message. (It might help if I understood how my own email filter worked :). Once again I was looking...	Christopher Mills millsspam	Mar 17, 2005 9:43 pm
8225	Chris, See my comments inserted below. Thanks, Craig Chadwick President Custom Solutions, Inc. (a.k.a., HomeVision) mailto:csi@... http://www.csi3.com ......	Craig Chadwick csi3	Mar 17, 2005 10:40 pm
8226	Hi, I have a need for a RJ45 switch box that can be controlled by X10 commands. That would be the ideal situation anyway. I'd settle for an RJ45 switch box...	Mun Johl mun_johl@...	Mar 17, 2005 11:02 pm
8227	Here's one capable of remote serial control... http://www.cpscom.com/gprod/abm.htm...	Dave Yeatman dyeatman1	Mar 18, 2005 4:09 am

Yahoo! Groups Tips

Did you know...

Messages

Yahoo! My Yahoo! Mail
	Sign In New User? Sign Up
		Groups Home - Help

Yahoo! Groups Tips

Did you know...

Best of Y! Groups

Messages