Hey guys, I have a HV-Pro Board set up switching some 24VAC loads on the relays and only a few PIR contact sensors into the input ports on the MFEB. My problem...
Hi Rob Do you know if the 24v ac (assuming irrigation solenoids?) relays activate during this resetting period ??? Im thinking maybe they do and causing some ...
Hey Frank, Thanks for the help. I live in Ireland so definetly no need of irrigation solenoids :). Basically I use the homevision relays to switch 24VAC loads...
Rob, When the "lock up" occurs during a download, do you have to cycle power to get it working again? I assume you've tried downloading the schedule again ...
Craig, Firstly, thank you for the assistance. That is exactly what I do - cycle power and it goes back to the normal status and takes the new schedule until at...
Hi Rob Might be an idea to put some suppression on both your 24v ac coils as well as your 240v contactor coils..this might help....What brand of control relays...
Rob, Your original message only mentioned a problem occurring during a schedule download. This message says "some later time it goes back into a constant ...
Craig, You are correct. This is a separate problem. While downloading the schedule it goes to the LED1 off and inf lit state (at 98% downloaded). This happens...
Hi Rob ... Schneider should have suppressers for those contactors....most likely an rc snubber (since its ac)... For dc relays they would have either diode...
Hello, I've an interesting problem with my HV and a module. I have an x-10 wall receptacle module unit which is working fine. For some reason, when I send an...
Easy peasy lemon squeezy... You have a switched mode PSU plugged into the module and after you turn it off then the PSU decays, the impedance changes and the...
Hey Phil, Thanks for that. I'll open up the module and cut that link, but, curiously, This problem only cropped up now.. It's been working fine for at least a ...
Y'all, Well, I would have preferred my introduction to the group to have been in a different vein, but I'm in need of some assistance in troubleshooting the...
Shawn, All the tests show the controller is communicating with the PC just fine. Are you using the schedule that came loaded in the controller, or did you ...
Anyone know where I can purchase the Sylva 8 channel IO boards (SC8O8IX-U)? I am getting no reponse to emails and telephone calls to the Sylva office so am...
Craig, Thanks for the quick reply! I'd just now gotten done with a response to your questions below, adding some more detail when I decided to do one last bit...
... The `short sweet' answer is yep! As an example: Up until about a month ago I had been running both HomeVision and WeatherLink on the same machine, a 3COM...
Bob Baldwin
bbaldwin@...
Jun 20, 2008 2:31 am
11519
The Smartlinc LED Detector Probe appears to have been discontinued. Has anyone tried to use the Xantec LED & Light Sensor Module ?? How did you connect it to...
I think Sylva is coming out with a new version of the boards, and they don't have any more of the older version in stock. I'm also not aware of any ...
Frank, Many thanks for the links you posted. I may get around to getting some of these supressors - however after sorting out the given problem alls good with...
Hey guys, I know this may be way out of my depth to attempt this but just seeing what the more learned ones in here may think of the possibility of success on...
Have a look at the mini-itx and nano-itx range of computers. http://www.mini-itx.com/ The artigo is an interesting nano-itx. I have a min-itx running a full XP...
I would stay away from special embedded OS versions or even non-x86 type processors, too much trouble getting everything ported or cross-compiled. Recently I...
Ruud
ruud3@...
Jun 24, 2008 4:58 pm
11526
Just saw this and was wondering if it would work with HomeVision. http://thingm.com/products/blinkm.html...
Rob, I agree with the other two responders that you will be much better off with a x86 based solution, maybe even a cheap old second-hand laptop running linux?...
... Unfortunately HomeVision's communication with an I2C slave is limited to sending one or two bytes, or reading one byte[*]. As I understand the blinkm...
Just came across this it comes with windows CE as standard but they do do a version of LINUX as a free download, if you want to run this instead. Not too sure...
Hi Rob ... I assume you are using the CBUS public release protocol...??....Thats what im currently using ,i have written a macro to control the lights which...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
