timandmaridith wrote: Date: Thu, 08 Jul 2004 07:31:31 Yes, the outhall cable sawed half way through two 3/8" bolts (for the main sheet hanger) before I...
My brother and I just got a 33, and we need have a few questions: ANy idea what a "tic tock" system is? The electronics need to be replaced, and that's what...
Hi Brad, Welcome to the Hobie 33 class. I think what the previous owner was recommending was to go with the Tactick,call me at 817-426-0439 I can help you...
I am looking for overall dimensions of a H33 on a trailer. I believe the trailer's are 30' overall, based on the dwg in the file section of this site. What I...
timandmaridith wrote: Date: Fri, 16 Jul 2004 Part of my annual safety check is to actually test my manual bilge pumps (2 for off shore racing). The "Guzzler"...
I am speaking with each of the trailer manufacturers located on the www.Hobie33.com webiste. I am a serious buyer of a fixed-keel trailer. Can anyone...
In a message dated 7/18/2004 10:24:13 PM Eastern Standard Time, ... If I were replacing my trailer, I would have it made with jack stand supports instead of...
Hi: I am looking for 2 lift keel Hobie 33s with no sails and trailers for US$10,000 each to match race in the Yucatan. Would like them to be near or around...
Another option is to purchase a used Trailrite powerboat trailer, with 5 1/2 inch frame rails, that is in outstanding condition, and have a welder use the ...
Another option is to purchase a used Trailrite powerboat trailer, with 5 1/2 inch frame rails, that is in outstanding condition, and have a welder use the ...
Are you going to charter these out. If so, I would be interested, where in the Yucatan? Mike Schiltz ... From: Michael Brindley [mailto:brinfin@...] ...
Any West Coaster's on the fence or interested in selling their Hobie 33? I'm based in the Bay Area. and yes, I have been checking all the usual classified...
I've never seen one closeup - just out on the water. Available to crew also if anyone is interested. I used to own and race a Holder 20 and like the...
I recently bought a lift keel version of the Hobie 33 which I am intending to sail andrace on the San Francisco Bay. My plan is to keep the boat in the water...
This has always made great discussion, however don't worry about it. The boat is fine with out messing with trying to seal the well. Barnacles have also not...
I recently acquired a lift keel boat that has heavily oxidized gelcoat both on the deck and hull. I have been performing other maintenance while considering...
In a message dated 7/29/2004 12:30:57 AM Eastern Standard Time, ... Contrary to some owners, I get a lot of barnacle growth in the keel well. I also have been...
Please forgive my posting this way, but all my messages sent through the yahoo web site were rejected. I have several issues with my boat, #46, Barbarella. 1)...
In a message dated 8/3/2004 7:57:13 PM Eastern Standard Time, ... I have had triangular stainless webs welded between the stancion tube and the bracket. Beep...
I removed all of mine and made sure that the doubling sleeve that was inside of them was properly welded as initially they weren't. Scheherezade ... From:...
coyote is heading to Key West, the section in 2004 was won by an Evelyn 32-2 , Evelyn's also took 2nd and 3rd. How will the Hobie 33 do in that chop and...
No. Good luck in Key West. Any idea how close we can get to a one design fleet there? . What brand of sails do you have? What is your rake? Is it as per the...
I am considering getting a keel boat and am interested in the Hobie 33. Is there anyone on this board that has a Hobie 33 in Chicago and would be willing to...
I have one on Lake Carlyle. terry ... From: shak1 To: hobie33@yahoogroups.com Sent: Thursday, August 19, 2004 2:12 PM Subject: [Hobie33] Any Hobie 33's in...
... that done ... tube and the ... weld on the rod that attaches to the stanchion and is thru bolted through the deck. Remove the stanchion from the boat. Then...