All - I have just received my new HF-Auto. I am very happy with the tuner. My antennas are tough to tune - a 130' doublet fed with home made open wire feeders...
The other day a local ham who had just received his HF-Auto ran into a problem in tuning. I was concerned since I am awaiting my unit ordered at Dayton. Paul...
It's an absolute no brainer if the tuner has not finished tuning you don't turn the Amp on and start applying high power. It's just plain common sense. KE4WY...
This tuner can tune with 1 watt. Done it here on every band 160-6; However I tune with the power that it takes to drive my Amp to legal limit and thats 40...
Received my HF-Auto a week or so ago....It tunes all my different antennas to a 1 to 1 match as it should...But does not seem to have a memory...If I switch...
My experience seems to suggest that there are memories and there are separate memories per antenna. However, there are some situations where, if the tuning for...
If you start tuning and quickly remove the signal, the tuner will continue to the memory for that frequency, showing that their are, indeed, memories. 73 de...
HF Auto Mod Requests 1. Amp Key Output - The purpose of the Amp Key circuit should be to prevent the amplifier from keying up while the HF Auto is tuning....
I apologize this was so hard to read and with extra spacing. I wrote it in Word first and pasted it which obviously didn't workout too good. I hope this came...
I have an at-auto and am considering the hf-auto. Since I am using an Orion II, I cannot use the CIV control and must hit TX to invoke tune with the at-auto. I...
I spoke to Paul yesterday regarding a glitch I was having with my HF Auto and asked about both the Amp keying circuit timing and the lack of a default bypass...
Bill, I have both the AT Auto and the HF Auto. The HF Auto is much easier to use since it tunes on an SSB signal and has a much simpler setup menu with much...
Received my HF Auto today after a repair and software upgrade from V1.04. One new option in the V1.05 menu is called Timing with options of 1,2 or 3. Does...
... From: k1zzi To: hf_auto@yahoogroups.com Sent: Tuesday, November 08, 2011 4:41 PM Subject: [hf_auto] V1.05 Firmware Upgrade Received my HF Auto today after...
It's pretty impressive when the president of the company responds in a matter of minutes! 73 de K1ESE John...
24
hf_auto@yahoogroups.com
Nov 8, 2011 11:07 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the hf_auto group. File : /Bulletin #...
I find that if I set the timing ( the delay between when the tuner doesn't detect any RF on the input and when the tuner's keying relay inkeys ) to 0 that the...
Now that was fast! Thanks for the Tech Bulletins Paul. Good to know about saving memory locations in Bulletin #2 too. That puts a memory question posted...
Greetings to all; I am considering a purchase of a PalStar tuner, and I have it narrowed down to the AT5K and the new HF-AUTO tuner. But I do have some...
I have the AT-AUTO, also the HF-AUTO as well as the AT5K. The HF-AUTO is working out well. The reason I purchased the HF-AUTO we to replace the AT5K which I...
Greg - I find the HF-Auto has more tuning range than other tuners I have used and will tune my 130' center fed doublet fed with open wire just fine on 160m. I...
Greg, I had a Palstar AT2K and just replaced it with the new HF-Auto. My concern was like yours for 40/80/160. I use a 160 meter Inverted "L" that has an SWR...
Hi Group,Quick Question on proper tuning of manual linear to hf-auto.New to the group,Can anyone tell me the proper way of tuning my AL-80B to the hf-auto...
After tuning the HF-Auto and getting the match, I then leave the HF-Auto in low power and tune the amp with low power. You should have an idea of a possible...
Let me clarify my earlier posting. You do not leave the tuner in low power (it is not adjustable) I leave the exciter (in my case the FT-2000) in low power...
