Time to thin out a little. I got these radios working good and once I do that they are no fun for me anymore. SB-110a 6 meter. Nice radio, full 100 watts out....
I picked this up from a friend a while back with the good intentions of finishing the build with my youngest son. With my limited electronics knowledge and my...
Any one have data to build coils for Heathkit Gd-1B griddip meter. I need to construct a set of coils, Need number of turns and size of form plse. Found one...
Hi Have gained one of theses less the case and missing the valve that plugs into the tuner unit. This unit is dated 1963 and a expect it was supplied ready...
Hello to all in the group, I just bought a Heathkit HW-16 Transceiver. What I would like to know is how can I make better. For ex. is there any mods for this...
I have a Heathkit TWOER with original mike, manual and power cord. Mint condition inside and out,looks brand new. Crystal socket moved to back panel and uhf...
Thanks Ron, Any help will be appreciated. 73 Ken Give Packet Radio a try .......Mississippi.......145.010.......Simplex.......1200 Baud ... From: Ron Pollack...
I am looking for one of the large green knobs for my SB-200. If you are willing to part with 1 or the whole set please let me know. Thanks, Bob - K2RET...
I have a SB104A transciever It works on 75. 40. 20. and 15 meters just find on SSb. When you shift to any of the 10 meters bands and key the 104a, It goes...
as it just so happens , i have a heathkit grid dip meter but not sure what model. i'll go out to the shed and see what i got and reply back asap. don't need it...
Whilst not being a 104 man (Me likes 101's), I did a have a non heath that had a similar problem on 10. The problem was one of neutralization of the finals. ...
Bob, The SB-104/104A transceiver has transistorized output. The PA is of a broadband type that isn’t really frequency dependant. There is a limit to output...
hi agn ken, the meter is a /heathkit GD-1250 solid state unit with a full complement of coils 9 every spce in the plastic storage box is filled. it goes all...
I am able to adjust the SWR calibration OK BUT, the power calibration is a problem...... Between the "Cal" and "Norm" switch positions one should be able to ...
First a little intro... I am bill, N8TLC and was introduced to the group by John W8QA. Hope I can be of help, rather than a pest. Now, my present problem: I...
The complete HM-9 manual can be downloaded from www.pestingers.net/Heathkit_manuals_sequential.htm The illustration and schematic book is also available as a...
ma.locksmith@...
Jul 8, 2007 1:46 pm
4377
Thanks Ron, I will be looking for the info 73 Ken Give Packet Radio a try .......Mississippi.......145.010.......Simplex.......1200 Baud ... From: Ron Pollack...
In the Subject line you state that it is a HR-1980, but in the body of your letter you say it is a HR-1680. I have been unable to find anything about a...
Hi The GR-78 receiver runs from internal Ni-Cad batteries charged through either AC mains or 12v 2 pin rear connections. I am looking for either a 12v plug or...
Although it doesn't look "original", I bought a small power supply from Ramsey Kits and ran the wires through the back of the case. That worked fine for me. ...
The AC cord, if I remember (my GR-78 is at home..!) is a non-polarized cheater type. Search: http://www.allelectronics.com/ with the keyword 'cheater' and you...
AHA. No sooner had I posted that I recalled the 12-V plug. It's a Cinch-Jones, round, two prong, polarized (one larger than the other). Allied Electronics have...
Hi, I recently purchased a Heathkit SS-9000 that included a generic hand mic that works well. However, I'd like to use a desk mic, but not sure what works...
Any of the Heath EV mikes will work well. You might call Bob Heil at his shop and he will also have some very good advice on a Heil mike. I used both with...
Thanks, Michael, I will see if I can find them here in Australia. Apparently it is now getting very hard for us to purchase from commercial US suppliers as...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
