hi TOM, have plans I drew up, will gladly give you a copy, you will still need to know the bed size to m/c gap. part made from m/s 2.5x3x5ins long, rod can be...
If you're referring to the v way angles, included angle is actually 70 degrees. I have a good drawing of the top surfaces, will post later today. ... M300 bed?...
Hi all, looking for a shaft for m300 part No 312-033, located in cross slide. do not know if m300 has two shafts in that position, one for none taper turning,...
While i get the general idea of the wiring the inverter to the lathe my problem is in wiring the inverter to the single phase supply. the instructions for the...
Steve open the cover and see if theres a wiring diagram, it could well be different to the manual. I have the two MA7200 a 7.5KW and a 4KW, the red, neutral...
I have just measured my M300 again and they are both 55 degrees. I assume my digi chinese protractor is accurate so put a 45 dgree dovetail cutter upside...
I'll have a look Stan but think everything went with the lathe inc full set of change wheels. My mate that has the 11" same lathe with round head had the...
I have the same inverter, came from direct drives, always found Dave a great helpful bloke. anyway also have a VXM Jaguar and an FVR from BSL. The VXM drive...
I think the older English made ones are all 70 degrees (as were Clausings), the more recent vintage are Chinese made and are something else. ... -- Lew...
There are very few inverters that are truly single phase. Most are actually three phase devices that can be fed from single phase (feed from three phase if you...
My British made 1999/2000 M300 has 70 degree vees. Annoyingly, Colchester Students/Masters had different vee angles, even though they were made in the same...
Stan which inverter are you wiring in? 7.5,4kw, Jag etc. Also is it plug and play or wired direct to motor with soft start etc. Currently using the (10hp)...
I always thought my M300 was quite old either side of the 70's. Did have a 600 Group sticker on end of bed, ex GKN machine sold after 2004, i found a despatch...
Hareng, Are you sure you should not subtractthe 10th degrees? If so, you'd be st 35 degrees, exactly 1/2 of 70 degrees. ... dovetail cutter upside against one...
That last message should have said: Are you sure you should not subtract the 10 degrees? If so, you'd be at 35 degrees, exactly 1/2 of 70 degrees. BTW, if you...
2183
harrisonlathe@yahoogr...
Feb 3, 2012 12:24 am
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the harrisonlathe group. File : /Harrison...
No Lew mine is 100% different to your upload. Where your 70 degree angle meets the bed flat height theres a ledge. On mine theres no ledge the angle is spread...
The inverter is a mitsubishi A024 Â Steve ... From: Stan Gordon <stan_cramlington@...> Subject: Re: [Harrison Lathe] help with wiring an inverter to a...
Make sure you note the serial number from the /rear/ vertical shear of the bed, not the one at the front. The front number is just some factory admin number -...
Gee whiz thats a powerfull inverter. I have 3 inverter/converter, 2 are chucking 415V 3 phase and the other 220V 3 phase. The lathe is an older model 140 and...
... Steve, I have Mitsubishi D700 inverters on my machines (two 750w and one 2.2Kw) and the 240v AC single phase inputs are labelled L1 , N, and E. Looking at...
sent you the manual to your E mail address in PDF -- wiring on Page 16, make sure you have the correct inverter, eg 240 single phase in and 3 phase out, there...
Looking at a different make of inverter, the Jaguar, the 240V single phase in, goes to L1/RÂ neutral L2/SÂ Blank L3/TÂ Live earth to earth terminal do make...
... Steve, OOOps! Slight error in my e-mail above what I meant to say was "240v single phase input to 240v 3 phase output inverter". My Mitsubishi D700s are...
I managed to get down the workshop today and took the front panel off the inverter, the terminals are totally different to the manual, they read from left to...
almost self explanatory, L1 = 240 live in N= Neutral 240 in, U, V and WÂ 3 phase out. Not too sure what the output voltage is, just make sure the motor...
... L1 would be Live. N is Neutral. + and - is probably a DC voltage used for logic switching in the inverter. Mine is 24v and depending how it is connected...
