hi again fella's, i bought a MT5 centre for my harrison L5A lathe off ebay, when i tried to fit the damn thing the centre protruded out of the spindle by 2...
Hi Bill, My L5 is an MT 3 anyway, I've never heard of a 4.5? Seamus. ... __________________________________________________ Do You Yahoo!? Tired of spam?...
hi seamus, im stuck on this one mate!, i dont know what this spindle is? it may well be an "odd ball", but there again it may be a MT5 or MT 4.5 i dunno,...
Hi. I have an L5A and had the same experience when I bought a MT5 center. It appeared to be the right taper but the dimensions were too big and it protruded....
Anyone have a taper attachment for their M300. I expect one could look for years and never find one of these used. If possible I would love to see some...
... Hi John. I've uploaded some pics to the photo section that I took of a taper attachment on a VS330 - I've put them in a sub folder in the 'M300' folder....
I recently bought what I beleve to be a 1959/60 Harrison L6 serial#96433 On statr up no drive to lead screw or power feed rod . Removed S.C.G.B. to find...
I recently bought what I beleve to be a 1959/60 Harrison L6 serial#96433 On statr up no drive to lead screw or power feed rod . Removed S.C.G.B. to find...
Hi Bill What thickness of sponge did you use in between the clutch plates and did it cover the full plate Ken...
198
harrisonlathe@yahoogr...
Aug 23, 2005 8:57 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the harrisonlathe group. File : /Chuck...
hi, i recently posted that a piece of sponge placed between the clutch plates will dampen down the noise from a noisey clutch,,well this does work for a while,...
hi, ive just fitted all new headstock bearings to my L5A, if you are interested to see the job been done i have placed a few photos of the refitting on my...
Good information and nice work. I posted a link to your Harrison page in the Links section. James bill <dampshed77@...> wrote: hi, ive just fitted all...
hi and thanks james for placing the website in the links section. its very thoughtful of you, best wishes to you, bill James McAllister <jmcalli@...>...
Hello everyone, I've got an ancient (1944?) L5. I beg to ask what are the best *current* lubricants for... * The bedways. * The gears in the apron and the...
l have a Harrison L5A which has a spindle bore of 1.1/4in which will not take the draw bar for 5c collet this being 1.3/8 Has anybody rebored a spindle or has...
hi fellas, im still none the wiser reference this spindle bore its supposed to be a mt5 but it doesent take a mt5 centre! and im really against boring this...
The Harrison has a 4.1/2 MT ... From: bill To: harrisonlathe@yahoogroups.com Sent: Tuesday, October 18, 2005 10:53 AM Subject: [Harrison Lathe] L5A spindle hi...
hi yall, would anyone have the drawing of the clutch assembly, i have the exploded view in the instruction manual but this does not give enough information,...
HI ALL, i have aquired the correct dimensions for anyone wanting to replace their clutch spacer washers, L5A manual item no;36 part no; L5-814 item no;37 part...
... hi, salman, if no one replies to your thread you can also try the yahoo cnc members at:- http://groups.yahoo.com/group/CAD_CAM_EDM_DRO/ there are a few...
hello to all. recently bought an M300, and she has a slight taper on her, getting greater towards the headstock. beds dont seem to have any wear on them, can...
... It's likely that your bed is twisted and so is throwing out the line of the cut. Use (or fit) adjusting feet to jack up the corner of the lathe that's ...
Hello, I have a L6 MK III and it is time for me to service the clutch, it is failing and noisy. I saw the post on the dia. of the L5 clutch components posted...
Well my clutch project has turned into starting a rebuild of the lathe (including having the ways ground). The clutch on my L6 is unlike the L6 manual that I...
As suspected it was the pin, just took a little more force to remove it. Does anyone have a parts diagram for this style clutch, it is unlike the manual that...
This group is pretty quiet as someone mentioned already. It would be nice if more people who have asked for help or suggestions could post back. Yeah, it...
