Has any kind person got a PDF of the above I could have a download of I am trying to install the adove model this weekend after spending the last few weekends...
There is a guy in England that sells good bound copies on EBay for a reasonable price - that's where I got mine from. Chris P To: harrisonlathe@yahoogroups.com...
If you talk to Harrisons part department, and pose the fact that you would have a problem identifying spares you may require, they usually offer to email you a...
Hi I am looking to find the length and width of a M250 , I have potential line one and before getting too interested in it I need to know if it will fit in my...
Hi Brice, If you are that tight, make sure you consider leaving some room to load stock if you are dealing with bar stock the width of the lathe (minus ...
I put my M300 at 90 degrees to the wall, with the tailstock towards it, leaving sufficient room to slide the tailstock off the bed. This gives the remaining...
Have attached a pdf spec sheet, though I'm not sure if the yahoo group will forward it, so also directly copied to you. You need some room at the headstock end...
thanks for the replies , looks like its a bit to long for my space ,sigh , I have dalton in that space now was hoping for a bit more power in the store , I...
Brice, If you're no longer in the market for the lathe and if it might be available to somebody other than you you might offer to assist with contact. Just a...
I know this is an old post but did anyone resolve the issue of the spindle bore taper for the L00 spindle used on the L5A??? Jarno 13? Morse 4.5?? Mark...
4.5 fitted my 140 with a L00 nose, I originally turned a wood one and kept it handy when I visited anyone selling eng stuff for a cross reference, it worked.I...
I'm about to strip my M300 to have the bed reground. Is there anything I should be aware of, either things to check or set ways to strip. Any help gratefully...
Could you give us a rundown or document your progress of how you are going about regrinding the bed? I have never seen it done and would like to know what's...
Hi All, Not had my M300 done, but I took my Bridgeport to Brian Caddy at Slideway Services - he reground the knee, saddle and table, refitted gibs, etc. He...
I have heard of slideway services but as I live in Ireland it would be cheaper (Maybe?) for me to buy a secondhand lathe than get one refurbished. I am sure...
bit lacking in detail but, http://www.youtube.com/watch?v=GlbKtYJJw-s Charlie ... From: "John Kiely" <john_kiely@...> I have heard of slideway services...
Hi Phil, If you are still after help with your L13, I have an L13 and what's more, I am also an Aussie, in the Sydney area. Where abouts are you? John....
Hi All, I have a Harrison L13 lathe from the late 50s/early 60s fitted with a 3 phase, 2 speed reversing motor. The contacts in the rotary switch that...
G'day John, Thanks for your reply to my old help post on the L13 Name plates. I eventually found the "Harrison" plate on Ebay from G and M Tools in the UK. I...
John, How bad are the ways that you need them to be refinished? Are you a hobbiest or is this machine going to be used for manufacturing purposes? Unless...
Hi Phil, I will arrange some photos for you. I know you are after the Hi Forward/Lo Forward/Hi Reverse/Lo Reverse plate. What else do you need? I agree that...
Hi John, The other plate missing is the feed fwd/rev on the front left of the headstock. My lathe has a lever, some have a rotating knob. Maybe a general view...
Ed it was Charlie who linky'd the video, so credit where credit is due. As I mentioned before I live in Ireland and a lot of what is on offer here Lathe wise...
Apologies if this is a duplicate as I posted Wed, but havent seen it in my Mail box, My 140 is def a 4.5 MT, could well be that the Jarno fits as well, I have...
sorry that link should be, and the 12" steady probably fits the L6 http://www.tools4cheap.net/products.php?cat=22 Stan ________________________________ From:...
I updated my post as the link was not right, apologies-- it too has not come into my mail box?? so this is yet another duplicate:::: so: Tools link:Â ...
Again apologies, I posted an update to the reply I gave, --Twice but nothing is comming through to my mail box, so I keep thinking the reply hasnt worked. The...
Thanks for the info Stan, I will give Jeff an email and see if he has the reducer. I didn't see it on the website. Mark PS 3 replies are better than NO...
