Hi All, This is the first time that I have been using my lathe on a phase converter. (Rotary 3HP). I am machining a back plate for a 6" chuck and my thermal is...
Hi Gerry. Don't know much about converters, but I owned a static one for a brief period and the salesman warned me I'd need a 5hp converter to drive a 3hp...
Gary, I dont have any details on the thermal cutout but measure the voltages in all of the 3 phase legs and make sure they are balanced pretty well when the ...
Hi All, Thanks for the comments. I decided to take out the thermal contacter. Guess what it had some electrical tape aroound it from a previous proble. Have...
Hello, I have a L6 MKIII 12" swing, I would like to know the correct procedure for preloading the headstock bearings, the manual that I have does not include...
Brad, Somewhat of a delayed response but here's my shot at it: non-Harrison reply - some makers suggest adjusting preload until a quick snap of a chuck will...
Hi All, Thanks again for the moral support. I spent some time perusing the wiring diagram. It states that for 220 volts, the thermal relay has a range of 4 to...
Den: Thank you for your response, to date it has been the only info I have been able to obtain. If I was to use the temperature method, what would you think...
Brad, One 11" Rockwell manual (US Army) says that if the temp rises to 145F, back the preload off. That's a bit high for me and I'd use something closer to...
hi fella's im making a set of change gears(finally) does anyone have the list of the wheels i require please, i have a few change gears but i would like the...
hi seamus,, thanx in advance for checking your change wheels, i usually go onto an engineering forum for quick answers as its a live forum, plenty of brains to...
hi fella's can anyone tell me which grease gun/oil gun is best suited to the harrison L5, ive tried using the standard grease gun which works fine but i cant...
Bill, On several other lathes, including the Harrison M300, oil is pumped in via the nipples (and the one shot system). The gun is a hand held cylinder about...
hi fellas, does anyone know the D,P for the L5A gears please?, god knows what the D,P stands for but i need to know for the gear cutters, i think i need to...
DP stands for diametrical pitch. You can use the formula on this link to calculate it for your L5A: http://www.boilerinvasion.org/files/kip/gears101.html ...
hi again fella's, i bought a MT5 centre for my harrison L5A lathe off ebay, when i tried to fit the damn thing the centre protruded out of the spindle by 2...
Hi Bill, My L5 is an MT 3 anyway, I've never heard of a 4.5? Seamus. ... __________________________________________________ Do You Yahoo!? Tired of spam?...
hi seamus, im stuck on this one mate!, i dont know what this spindle is? it may well be an "odd ball", but there again it may be a MT5 or MT 4.5 i dunno,...
Hi. I have an L5A and had the same experience when I bought a MT5 center. It appeared to be the right taper but the dimensions were too big and it protruded....
Anyone have a taper attachment for their M300. I expect one could look for years and never find one of these used. If possible I would love to see some...
... Hi John. I've uploaded some pics to the photo section that I took of a taper attachment on a VS330 - I've put them in a sub folder in the 'M300' folder....
I recently bought what I beleve to be a 1959/60 Harrison L6 serial#96433 On statr up no drive to lead screw or power feed rod . Removed S.C.G.B. to find...
I recently bought what I beleve to be a 1959/60 Harrison L6 serial#96433 On statr up no drive to lead screw or power feed rod . Removed S.C.G.B. to find...
Hi Bill What thickness of sponge did you use in between the clutch plates and did it cover the full plate Ken...
198
harrisonlathe@yahoogr...
Aug 23, 2005 8:57 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the harrisonlathe group. File : /Chuck...
hi, i recently posted that a piece of sponge placed between the clutch plates will dampen down the noise from a noisey clutch,,well this does work for a while,...
