Weds 12/1/04 Another email from Ladislav in my inbox. "Glenn, next week we probably will release new Build 5 of Embird 2004, and it will work with trimms the...
Hi all, It's probably been asked before but please, support the aged!!! What offset does one allow when setting up a user defined frame on the Voyager? Barry....
I have totally given up on setting that info. Glenn mentioned ( I think it was him) that his machine nevers knows what size hoop he is using, well I do the...
That was me. I never bother telling the machine what hoop I'm using. I center the design with Embird and shoot it to the controller with HappyLink. Then I...
An interesting about face from the previous message he sent isn't it? Something tells me they took a harder look at the issue afterward. ... HOOO! Look at ... ...
Hi everyone, I am trying to attach my hat hoop for the first time and I need some advice. My rail bracket hangs under the rotary cylinder and it looks like it...
Hi Roberta, The rail bracket should attach to the same spot where the frame base attaches using the same three screws you use for the frame base. When I...
Getting that pin pushed in so the hoop is recognized is the trickiest part on my Happy. WOW is it temperamental. Could be just my machine. But if I hold my...
Thank you for responding, I can't figure out where the wire is supposed to be and what they are for. My rail bracket hangs by this wire when I hold it in...
Hi-This is my first time posting with this group so be easy on me!! The upper thread keeps breaking right at the needle point. I have set the bobbin tension by...
John, If this is on all needles, then the upper tension is probably wrong, if it is only on a few needles, check to see that they are installed properly. You...
This may sound dumb, John, but is it possible you have them in backwards?? The scarf (the little flat spot above the eye) should be in the back, and the long...
Linda: The needles are all in properly and straight. It does not break on all needles. I have tried to make the tension on those that break the same as those...
John: Another thing to watch for is the thread path. Make doubly sure it is correct. Even RE-thread if in doubt. I find also the thread will slide off the...
I have one just like it, I brought from a different vendor. I would not do without one. When you have problems with thread breaks or looping, check your upper...
I have a couple of question on the gauge. You set it at a 120 to 150 what? GRAMS??? Also where do you connect the gauge on the thread?? uzone2 ... mine...
I want to thank everyone for their input. I took everyone's suggestions and rechecked the machine and I just ordered the upper tension gage. I will let you...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the happyembroiderymachines group. File :...
happyembroiderymachin...
Dec 11, 2004 4:00 pm
872
I belive it is grams, but it is keyed of their spring scale, details on the instructions are posted in the file section TOP TENSION GAUGE.PDF Kevin ... 150 ......
This Tajima gauge has been the best tension gauge for years and it still is Fred Fred Lebow Vice President - Non Wovens - Embroidery Stabilizers HTCW...
Becky, SWF frame brackets are a different width. You can change the hoop brackets, but if you are buying new hoops, Happy industrial machine hoops fit the HCS....
Hi, Adam, I hope you are online. I have lost Michaels's phone number and I really need to set up the hat hoop on my machine. I can follow the directions,...
I guess this is the 'nudge' I needed to do it. I also ordered the Tajima Gauge today. The slogan - "If your not checking your tension, your just guessing" -...
Roberta, The HCS Cap Driver is one unit, including the spreader bar, cable, and drum. The cable goes from the top of the spreader bar, around it's ends and...
