Hi all I am using HRD to control an FT857 via the cat interface now this part works fine however if I try using the command tester I get com port in use error...
Hi Andy and others, ... First of all, download and read the Command Tester docs from: http://sysgem.decus.ch/hb9drv/CommandTester.pdf You need to open HRD...
Hello everybody The scheme "Mark-V" is now available in the files section. The selfmade font for the frequency display is attached, too, but there are only...
Hello All, I have also had trouble interfacing with my Kenwood TS B 2000, (The Silver Box). The unit has the remote head connected the (RC2000). The computer...
Make sure that your 706 is not set to auto baud for the speed setting set it at 9600 or 19200 and set HRD to the same, this should work . Auto baud does not...
Working fine with my 718 here . What interface and settings are you using? DE Jimmy (WB8NBI) ... From: microphill74 To: ham-radio-deluxe@yahoogroups.com Sent:...
Tad, I had the same problem at first. I've got HRD setup as follows: Whatever your com port, speed 19,200 (in radio and HRD), CI-V address 58, DTR and RTS...
Hi all, ... It's sometimes worth using lower speeds with 'alternative' interfaces. Try it at 9600Bd (or even lower) and once it works, just ramp up the speed...
I did use an old S3 2MB video card from my old P133 for the second monitor. HRD and PSK de luxe don't support dual monitors very well at the moment. It works,...
Nope, the cards don't have to be identical (can't be since there is only 1 AGP bus for a videocard :)) 73, Ben (PG5S) ... Van: G8IFF/KC8NHF Nigel A. Gunn...
Hi all, I'm using an Asus dual-head card - no farting around with various drivers, and it works like a dream. However, it does have more computing power than...
Jimmy, I'm using a homemade CT-17 like interface. The settings on the radio CIV Baud auto, CI-V address 5E, Ci-V transcieve on, and civ 731 mode off. What...
Using same, turn you speed to 9600 or 19200 baud in radio and software make sure they are the same. Also turn on dtr & rts to on in the software it should work...
... From: "Florence Garneau" <f ... menu. ... worth ... Thanks, but yes I've checked all of that. ;-) I've been meaning to build a breakout box with LEDs...
Hmmm, with the CT-17 interface you don't have to set the DTR and RTS on (The CT-17 doesn't take it's power from the serial port). Also make sure you turn OFF...
Hi Tad and others, ... How's your interface powered? Using the comport to power it if you have a notebook can cause problems - lots of comports aren't exactly...
... There is no problem with the CI-V TRN being ON. In fact, some programs use it to provide a faster response when the frequency or mode is changed on the...
Well... Almoust all newer cards with Nvidia, ATI or Matrox chips (probably the 3 largest chip-makers) has dual monitor capabilities. They comes standard with...
Hi Jean-Marie and others, ... frequency or mode is changed on the radio. Maybe: but we have found it useful to turn it off sometimes! In fact, with HRD v1.0 it...
Sorry, guess I missed the instructions for the UltraEdit. It may have been sent off list. Would someone send to me direct so as to not use up the group...
Does the HRD command for the AGC on the 8500 change it from fast to slow or from on to off. The control commands on page 35 of the manual indicate on and off...
Hi all. HRD work OK in my 706 MK II G ,IZ2BKT,TRX Manager too The problem is in PSK31 ,the com port not work , in another program like Digipan MMSSTV CWTYPE...
Hi Craig and others, ... needs ... Thanks. Craig Many Icom rigs don't show anything on the display if the AGC is set to slow - you'll get an indication if it...
Hello' Peter, David, Igor and all 706 owners... I hope the following is not considered OT... And I hope it could lead to something new in 706 computer...
... it ... I was going to complain to Simon that my FT847 required an extremely slow input when manually entering frequency, but reducing from 57600 to 4800...
Hi Alan and others, ... has ... Maybe a silly question, but what sort of interface are you using? ... Hmmm.........where's Igor? 145, Pete/Igor PH1PH - G7ECN...
... From: "Joe" ... It's an interesting solution to the problem, I'll give it that. However, I would need to buy a cable, that I would then butcher, and find ...
